Attention

When placing an order for parts, be sure to list the Part No., Model No. and the description of each part. Otherwise, the non-delivery of the part or the delivery of a wrong part may result. 2. Please make sure that Part No. is correct when ordering. If not, a part different from the one you ordered may be delivered. 3. Since the parts shown in Parts List or Preliminary Service Manual may have been the subject of changes, please use this Parts List for all future reference.

How To Use This Parts List

This Parts List lists those parts which are considered necessary for repairs. 2. Parts not shown in the Parts List will not in principle be supplied. D SCHOT 1S30-J T05 D SCHOT 1S30-J T05 These reference symbols correspond with component symbols in the Schematic Diagrams. BT BID30X06STL BNI EATRH LOCK AC CORD 250S KP300 KS16A H B J J AC CORD 200SKP30KS B AC A AC CORD 250 KP4819D KS31A B E B England V Germany E Europe x1 Japan X4 Universal Area This number corresponds with the individual parts...

Specifications

100-240V AC 50 60Hz 70W (27W without options) 526 (W) x 170 (H) x 453 (D) mm (with LCD tilted down) 320 x 240 dots grey-scale graphical LCD w back light 180 120 (16 24 bit) seconds mono FS 44.1kHz 166 110 (16 24 bit) seconds mono FS 48kHz 82 53 (16 24 bit) seconds mono FS 96kHz 90 60 (16 24 bit) seconds stereo FS 44.1kHz 83 55 (16 24 bit) seconds stereo FS 48kHz 40 26 (16 24 bit) seconds stereo FS 96kHz 168-pin DIMM (PC133 PC100, CL2) slot x 2 3 x Envelope generators (2 multi-stage) 16...

Safety Check After Servicing

After servicing, make measurements of leakage-current or resistance in order to determine that exposed parts are acceptably insulated from the supply circuit. The leakage-current measurement should be done between accessible metal parts (such as chassis, ground terminal, microphone jacks, signal input output connectors, etc.) and the earth ground through a resistor of 1500 ohms paralleled with a 0.15 iF capacitor, under the unit's normal working conditions. The leakage-current should be less...

Safety Instructions Informations

Parts identified by the symbol are critical for safety. Replace them only with the parts number specified. 2. In addition to safety, other parts and assemblies are specified for conformance with such regulations as those applying to spurious radiation. These must also be replaced only with the specified replacements. Examples Noise blocking capacitors, noise blocking filters, etc. 3. Use specified internal wiring. Note especially 1) Wires covered with PVC tubing 4. Use specified insulating...

Test Mode

To enter the Panel Test Mode, press the GLOBAL key while holding down the SHIFT key in the GLOBAL page F1 of the GLOBAL Mode. Moving the Q-link knobs changes the graphics accordingly. Tapping the PAD shows the amount of pressure applied on the bar graph. Switching the FOOT Pedal on off changes the graphics accordingly. Turning the JOG wheel increases decreases the value in the Data field. Pressing the key shows its name at the bottom of the screen. For those keys with the LED, the LED is turned...

OS Update Procedure

The OS update can be made from the PC via the USB port. You must have the OS loader software for MPC4000 besides the OS .bin file. The OS loader software includes the OS Loader.exe file, USB driver.inf file, and USB Driver.sys file. 1. Install USB Driver to your PC After all files are un-Zipped, place the USB Driver.inf and USB Driver.sys files into the same folder, e.g. Driver. Boot up the PC and MPC4000 complete and then connect the sampler to the PC using the USB cable. This prompts that the...