Test Patch Set Up

Sliders and switches not illustrated should be all the way down.

4.1 Board A

REF.

FUNCTION

SET - UP

SPECIFICATION

GENERATOR OUTPUT

12V - 20V p-p (typical)

J4A-2

GATE INPUT

1. Pluck a string.

+0.6V PLUCK

OV PLl

JCK 1(

) rT

s

End of tone

J5A-3

GATE OUTPUT

1. Pluck a string.

m

End of tone

OV PLl

JCK 1C

s

J5A-4

TRIGGER OUTPUT

1. Pluck a string.

0.2

ms

PLUCK

SENSITIVITY

OUT

1. Trigger sensitivity maximum.-

2. Trigger sensitivity minimum.-

►10mV (typical) ►14V (typical)

J3A-6

FILTER CONTROL VOLTAGE

1. Plug filter pedal in.

2. Put Envelope Follower Select Switch in PEDAL position.

3. Fully depress pedal.-

4. Put pedal at minimum.-

■►11.5V (typical) ►OV (typical)

Z11A pin 1 (Q output)

SYSTEM ON/OFF VOLTAGE

1. Depress the system ON/OFF Button.

+ 15V = ON OV = OFF

REF.

FUNCTION

SET-UP

SPECIFICATION

TP-1

1. Initial Frequency sliders midposition.

2. All other sliders down.

TP-2

1. Initial Frequency sliders midposition.

2. All other sliders down.

TP-3

1. Initial Frequency sliders midposition.

+15V

TP-4

1. Initial Frequency sliders midposition.

2. All other sliders down.

TP-5

SQUARE WAVE OUTPUT (VCO 1 & 2}

1. Initial Frequncy sliders midposition.

TP-6

SAWTOOTH OUTPUT (VCO 1 & 2)

1. Initial Frequency sliders midposition.

2. All other sliders down.

LFO TRIANGLE OUTPUT

1. LFO Frequency slider up.

LFO SQUARE WAVE OUTPUT

1. LFO Frequency slider up.

2. LFO/KYBD slider switch:up (LFO)

3. LFO Frequency slider up.

TP 10

ADSR INVERTER

1. Put all ADSR sliders at

2. Pluck any string, (repeat switches all up).

TP-11

TRIGGER PROCESSOR

1. Pluck any string.

-15V

REF.

FUNCTION

SPECIFICATION

TP-1

CV INVERTER

2. All other sliders down.

3. Pluck the Low E string.

4. Pin high 'C' on the keyboard

VCF OUTPUT

1. Raise the VCF 'VCO 1 sawtooth' slider.

2. Raise the Initial Filter Frequency slider.

3. Put all other sliders down.

TP-3a

VCA OUTPUT

1. Raise the VCF 'VCO 1 sawtooth' slider. 2*. Raise the Initial Filter frequency slider.

3. Raise the VCA gain slider.

4. Put all other sliders down.

1. All repeat slide switches under the ADSR should be UP.

2. Depress and release a key.

L OV

3. Repeat switch: AUTO position (down).

L OV

TP-5

AR OUTPUT

1.AR Attack slider:1^

2. AR Release slider: 1/2

3. Depress and release a key (all repeat switches up).

String Plucked

+10V

TP-6

ADSR OUTPUT

1. ADSR Attack slider: 1/2

2. ADSR Decay slider: 1/2

3. ADSR Sustain slider:'/2

4. ADSR Release slider:'/2

5. Depress and release a key (all repeat switches up).

String Plucked

String Damped I I

0 0

Post a comment