Info

I. ' n n i i n n n n n n n U U H U U M U V S U U F U U SF n n i i n n n n n n n U U H U U M U V S U U F U U SF This mode determines if the offset value against a master machine should be displayed or not when the FD-8 is working as a slave machine. If you would like to turn ON the offset display, press the EXECUTE YES key while is blinking. (The default setting is off.) Then, turn the jog dial C.W. to change the display to ON and press the EXECUTE YES key. In order to display the offset...

Risk Of Electric Shock Do Not Open

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. POUR VITER LES CHOCS LECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU' AU FOND. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS...

Safety Instructions

Read instructions - All the safety and operating instructions should be read before the appliance is operated. 2. Retain instructions - The safety and operating instructions should be retained for future reference. 3. Heed warnings - All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow instructions - All operating and use instructions should be followed. 5. Water and Moisture - The appliance should not be used near water - for example, near a bathtub,...

Shoutl Rstoutl

P o p o 'I VVV' o i .f) i CAUTION In order not to form a MIDI signal loop, connect the MIDI cable after putting the FD-8 into the Service Mode. To start the Self Check mode, press the EXECUTE YES key when is blinking. As shown in the left, SelfCheck, CurrentDr, name of _ connected SCSI drive (The example on the left shows that 441kHz the Magneto Optical drive MOS350 is connected to the FD- 8 SCSI port.) and ATA Bus C (check) appear on the FD-8 LCD display in order. If a 2.5 internal E-IDE hard...

Table Of Contents

CONTROLS, INDICATORS AND CONNECTORS 7 3. SOFTWARE 4. SERVICE 5. ERROR CODE 6. INSTALLING 2.5 INTERNAL HARD DISK DRIVE 20 7. EXPLODED VIEW, PCB ASSEMBLY AND PARTS LIST 23 8. CIRCUIT * Service mode, error code list, exploded view, PCB assembly, parts list and circuit diagrams are given in this

Vari Pitch Tempo

If the FD-8 is in a normal condition, all the segments on the LCD display will be lit solid and all the LEDs on the top panel will start blinking. If the FD-8 is not in a normal condition, faulty segments on the LCD display and or LEDs on the top panel will remain unlit. In this condition, if the EXECUTE YES key is pressed one more time, the Button Test can be executed. The Button Test checks if each key button and jog dial are working properly or not. The display on the left indicates that the...

3 Software Update

Same as the FD-4, the FD-8 software can be updated through the SCSI port. This means that unscrewing and opening up the FD-8 top panel is not necessary to change the EPROMs. Please refer to the following explanation for correct software updating procedures. 3-1. Method of Sending Software from Fostex Japan There are two ways of sending the FD-8 updated software. 1. Updated software in a removable medium (e.g. floppy disk, zip disk, etc.) to be sent via airmail 2. Updated software as an...

Fostex Part Number 8277465018

Fostex Fd4 Internal Ide

There was improper access to program management region when saving System File. There was improper access when fading in out. 6. INSTALLING 2.5 INTERNAL HARD DISK DRIVE The Model 9045 and a 2.5 E-IDE hard disk drive installing procedures are explained below. Bracket, HD, FD-4 8 P N 8221234000 x 2 Connector, PI, header, 50P, P2.0, A3E-50PA P N 8245314000 x 1 Cable, flat, 2P, L150 P N 8276292015 x 1 Cable assy, flat, 50P, P1.0, L180 P N 8277465018 x 1 1 Loosen 17 x screws BBT 3 x 8 BZn fixing the...