3 Software Update

The FD-4 software can be updated through SCSI port. This means that unscrewing and opening up the FD-4 top panel is not necessary to change the EPROMs on the MAIN PCB assy. Please refer to the following explanation for correct software updating procedures. 3-1. Method of Sending Software from Fostex Japan There are two ways of sending the FD-4 updated software. 1. Updated software in a removable media (e.g. floppy disk, zip disk, etc.) to be sent via airmail 2. Updated software as an attachment...

4 Service Mode

There are various optional modes available in the FD-4 Service Mode. Please utilize them when servicing the unit. The way of putting the FD-4 into Service Mode is as follow. 1) Connect a SCSI device, insert the diskette formatted by the FD-4 and turn it on. 3) While holding down the STOP button and SHIFT key, press the SETUP key. As shown below, by rotating the jog dial C.W. or C.C.W., various optional modes will be displayed in addition to the general SETUP menus. In order to select a certain...

8230 1382

R537 837 8230 1382 20 HT, carbon, 1 4W, 22Q, 5 R540 840 82402500 00 Pot., PI, SL45, 50kQA, NS-4502VP, L20 R541 841 8240 2680 00 Pot., PI, RT09, 10kQB, CC, EVUF3A, L20 R542 842 8240 2700 00 Pot., PI, RT12, 50kQCC, R543 843 8240 2510 00 Pot., PI, RT09, 50kQB, CC, EVUF3A, L20 R544 844 8240 2510 00 Pot., PI, RT09, 50kQB, CC, EVUF3A, L20 R545 845 8240 2510 00 Pot., PI, RT09, 50kQB, CC, EVUF3A, L20 R546 846 8240 2510 00 Pot., PI, RT09, 50kQB, CC, EVUF3A, L20 R547 847 8240 2490 00 Pot., PI, RT12,...

8232 8011 00 8232 8011 00 8232 8011 01 8232 801101 8232 1431

VT, ALU, 16V SME-VB VT, CER, 25V, VT, ALU, 16V SME-VB VT, CER, 25V, VT, ALU, 10V SME-VB VT, CER, 50V, VT, CER, 50V, VT, ALU, 16V SME-VB VT, CER, 50V, VT, CER, 50V, VT, ALU, 10V SME-VB VT, ALU, 10V SME-VB VT, CER, 50V, VT, CER, 50V, VT, CER, 50V, VT, CER, 50V, VT, ALU, 16V SME-VB 10pF, 5 , SL 10pF, 5 , SL , 10 F, 20 , 10pF, 5 , SL 22pF, 5 , SL , 47 F, 20 , 10pF, 5 , SL 10pF, 5 , SL 100pF, 5 , SL 100pF, 5 , SL , 10 F, 20 ,

8232 8181 04 8232 8181 04 8232 8181 04 8232 8181 04 8232 8181

VT, CER, 50V, 10pF, 5 , SL VT, CER, 50V, 10pF, 5 , SL VT, ALU, 10V, 47 F, 20 , SME-VB VT, CER, 50V, 10pF, 5 , SL VT, CER, 50V, 10pF, 5 , SL VT, ALU, 16V, 10 F, 20 , SME-VB VT, CER, 50V, 470pF, 5 , SL VT, CER, 50V, 470pF, 5 , SL VT, CER, 50V, 100pF, 5 , SL VT, ALU, 16V, 10 F, 20 , SME-VB VT, CER, 50V, 100pF, 5 , SL VT, ALU, 10V, 47 F, 20 , SME-VB VT, CER, 50V, 100pF, 5 , SL VT, CER, 50V, 100pF, 5 , SL VT, PES, 50V, 0.022 F, 5 , AMZ VT, CER, 50V, 100pF, 5 , SL VT, CER, 50V, 100pF, 5 , SL VT, PES,...

Cc20r

8232 1434 76 VT, ALU, 16V, 47 F, 20 , SME-VB N A N A 8233 5041 03 ST, CER, 25V, 0.01 F, 10 , CC20R N A 8232 1434 76 VT, ALU, 16V, 47 F, 20 , SME-VB N A 8233 5041 03 ST, CER, 25V, 0.01 F, 10 , CC20R N A N A 8232 1431 06 VT, ALU, 16V, 10 F, 20 , SME-VB N A 8233 5041 03 ST, CER, 25V, 0.01 F, 10 , CC20R N A N A 8233 5041 03 ST, CER, 25V, 0.01 F, 10 , CC20R 8232 1431 06 VT, ALU, 16V, 10 F, 20 , SME-VB 8233 5041 03 ST, CER, 25V, 0.01 F, 10 , CC20R 8233 5021 04 ST, CER, 50V, 0.1 F, +80, CC20F N A 8233...

Info

ST, carbon, 1 10W, 0Q, 5 ST, carbon, 1 10W, 220Q, 5 ST, carbon, 1 10W, 10kQ, 5 ST, carbon, 1 10W, 100Q, 5 ST, carbon, 1 10W, 10kQ, 5 N A ST, carbon, 1 10W, 1kQ, 5 ST, carbon, 1 10W, 1MQ, 5 N A ST, carbon, 1 10W, 10Q, 5 ST, carbon, 1 10W, 100Q, 5 ST, carbon, 1 10W, 20kQ, 5 ST, carbon, 1 10W, 12kQ, 5 ST, carbon, 1 10W, 10kQ, 5 ST, carbon, 1 10W, 10kQ, 5 ST, carbon, 1 10W, 330Q, 5 ST, carbon, 1 10W, 330Q, 5 N A N A ST, carbon, 1 10W, 100kQ, 5 ST, carbon, 1 10W, 10kQ, 5 N A ST, carbon, 1 10W, 100Q,...

Notes

* Service mode, error code list, explode view, PCB assembly, parts list and circu manual to assist the service technician in maintaining the Model FD-4. * The following accessories are supplied with FD-4 as the standard accessories. Owner's manual 8288414100 (for export model) * Following is the packing material for the Model FD-4. Carton, inner, FD-4 8228716000 Packing, side, L, FD-4 8228440000 Packing, side, R, FD-4 8228441000

Phones

Crosstalk Click Noise Power on off Other switching MIDI Controlling -20 dBV p-p or less -50 dBV p-p or less Operation check should be executed using the test mode with connecting the MIDI IN and OUT terminal. RECORDER SECTION Frequency Response Fs 44.1 kHz Fs 32 kHz Full Scale Output Level (Ref -12dB) Dynamic Range Total Harmonic Distortion Fs 44.1 kHz Fs 32 kHz Channel Separation 20 20 kHz +1, -2 dB 20 14.5 kHz +1, -2 dB +2 dBV 1 dB (Fs 32 kHz 44.1 kHz) 88 dB or more (Fs 32 kHz 44.1 kHz) 80 dB...

Red

J501 801 8245 2980 00 Connector, PL, jack, phone, LGR4609-7000 S001 8253 6550 16 SW, PI, slide, 4-3, non-shortening, SSSF0, L09 S701, 801 8253 6550 13 Switch, PI, slide, 2-3, non-shortening, SSSF0, L09 S502 802 8253 6550 13 Switch, PI, slide, 2-3, non-shortening, SSSF0, L09 W001 8276 7770 20 Cable assy, 7P, WHTMT F-MT BS, L200 W002 8276 7790 30 Cable assy, 9P, WHTMT F-MT BS, L300 W010 8276 7780 20 Cable assy, 8P, WHTMT F-MT BS, L200 W011 8276 7790 20 Cable assy, 9P, WHTMT F-MT BS, L200 W012...

Safety Instructions

Read instructions - All the safety and operating instructions should be read before the appliance is operated. 2. Retain instructions - The safety and operating instructions should be retained for future reference. 3. Heed warnings - All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow instructions - All operating and use instructions should be followed. 5. Water and Moisture - The appliance should not be used near water - for example, near a bathtub,...

Scsi

In this condition, if the EXECUTE YES key is pressed one more time, the Button Test can be executed. The Button Test checks if each key button and jog dial are working properly or not. The display on the left indicates that the RECORD button is pressed. (K stands for the Key and J the Jog dial.) The display on the left indicates that the jog dial is turned C.W. The table below shows the relationship between the key button jog dial and the corresponding numbers appear on the LCD display. In...

Sync Out

This mode determines if the offset value against a master machine should be displayed or not when the FD-4 is working as a slave machine. If you would like to turn ON the offset display, press the EXECUTE YES key while is blinking. (The default setting is off.) Then, turn the jog dial C.W and press the EXECUTE YES key. In order to display the offset value, select the MTC by the TIME BASE key and the REMAINING TIME as DISP SEL key. 1. There might be a case that the percentage display does not...

Table Of Contents

CONTROLS, INDICATORS AND CONNECTORS 7 3. SOFTWARE 4. SERVICE MODE 12 5. ERROR CODE 6. INSTALLING 2.5 INTERNAL HARD DISK DRIVE 20 7. EXPLODED VIEW, PCB ASSEMBLY AND PARTS LIST 24 8. CIRCUIT * Service mode, error code list, explode view, PCB assembly, parts list and circuit diagrams are given in this Parts marked with this sign are safety critical components. They must always be replaced with identical

Wht

J101, 201 8245 2850 00 Connector, PL, jack, RCA, 1P, YKB11-0923, W S L001 003 8276 9130 00 Wire, jumper, isolation, L004 8242 1962 23 Coil, PVT, 22 H, LF5.0S L005 N A L006 8242 1962 23 Coil, PVT, 22 H, LF5.0S L007, 008 8242 1860 13 Filter, T, EMI, L010, 011 8242 1860 13 Filter, T, EMI, L013, 014 8242 1860 13 Filter, T, EMI, L017 021 8242 1860 13 Filter, T, EMI, L101 201 8242 1860 13 Filter, T, EMI, LFW7B-M3R2T L102 402 8242 1860 13 Filter, T, EMI, L103 403 8242 1860 13 Filter, T, EMI, S001 8253...

Apunch Rhsl Take

This mode tests if all the segments on the LCD display and the LEDs on the FD-4 top panel are correctly working or not. To execute this test, press the EXECUTE YES key while is blinking. liiSi iiiii sssss I mTCi digital 32kHz 44.1kHz 48kHz j rMlDTI SLAV SETUP MTC OFFSET REMAIN ABS ff ff ft BAR ff ff J ft CLK ff MB F LOC MTC IN O O H O O M O O S _ O O D . O O SF HHHHHHHHHH VARI PITCH TEMPO PGM i i i i h h h h h h i sync out m drive i I CLK MTC I I IDE SCSI i h h h h h h h h i auto i i a.punch i...

Scsi Apunch

To start the Self Check mode, press the EXECUTE YES key when is blinking (condition indicated in the previous page). As shown in the left, SelfCheck, Initial , name of connected SCSI drive (The example in the left shows that the ZIP drive is connected to the FD-4 SCSI port.) and ATA Bus C (Check) appear on the FD-4 LCD display in order. Since a 2.5 internal E-IDE hard disk drive is not installed in the FD-4, the Self Check mode comes to a standstill at ATA Bus Check test. In order to continue...

99

Fostex Fd4 Internal Drive

There was improper access when fading in out. 6. INSTALLING 2.5 INTERNAL HARD DISK DRIVE The Model 9045 and a 2.5 E-IDE hard disk drive installing procedures are explained below. Bracket, HD, FD-4 P N 8221234000 x 2 Connector, PI, header, 50P, AMPMOD P N 8245314000 x 1 Cable, flat, 2P, L150 P N 8276292015 x 1 Cable assy, flat, 50P, P1.0, AMPMOD, L150 P N 8277465015 x 1 1 Loosen 14 x screws BBT 3 x 8 BZn which fix the FD-4 Top Panel section to the Bottom Panel section. 2 Remove the following...

Risk Of Electric Shock Do Not Open

CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER OR BACK . NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SOLT, FULLY INSERT. POUR VITER LES CHOCS LECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU' AU FOND. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important...