1 Specific Channel Setting mode

In this mode, specific settings can be made for up to 12 channels. For channels that do not have specific settings, the settings of General Setting mode are applied. Select a channel or line input (L1-L3) on which a specific setting is to be made. 2 Press the I ESC I then I CHP TIMl keys on the remote control unit for servicing. General Setting mode is displayed._ Press the I DIG ANAl key in General Setting mode. Specific-Channel Setting mode is entered. How to exit Press the I ESC I key on the...

2 Simple Diagnosis of DV

OK Initialization of 1394 LINK and DV decoder inside PRISM2 appropriately completed NG Initialization of 1394 LINK and DV decoder inside PRISM2 has not been completed properly. Defective IC1001(PRISM 2) IC5101(1394PHY), improper connection between IC1001 1C5101 defective soldering, etc. Check the number of DV devices when one DV device is connected to the recorder 01 The connected DV device is correctly identified. Other than 01 The connected DV device is not correctly identified. Defective DV...

5 Pcb Parts List

NOTES Parts marked by NSP are generally unavailable because they are not in our Master Spare Parts List. The A mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. When ordering resistors, first convert resistance values into code form as shown in the following examples. Ex.1 When there are 2 effective digits (any digit apart from 0), such as 560 ohm and 47k ohm (tolerance is shown...

7110 Setup Sequence

System Codec IC (Initial Program Loader) DVD-R RW Drive Initializat peripher register an< Request for power off of system-control computer made to Tuner FL microcomputer System-control computer is turned off (entering standby) following request from Tuner FL microcomputer CPRM ERR displayed on FL display HDD ERR displayed on FL display *1 If both the drive ID check and starting ID check of HDD failed, CPRM ERR is first displayed on FL display. The dictionary data for the HDD are stored on the...

7111 Disassembly

Note 1 Do NOT look directly into the pickup lens. The laser beam may cause eye injury. Note 2 Even if the unit shown in the photos and illustrations in this manual may differ from your product, the procedures described here are common. Note 3 For performing the diagnosis shown below, the following jigs for service is required Emergency disc ejection rod (GGF1529) Flexible cable for service (GGD1284), (VKP2291), (GGD1437) Extension board (GGF1532 (A)), (GGF1532 (B))

716 Dv Service Mode

To check whether communication between a DV device and the unit is normal when a DV device is connected Remote control unit for servicing (GGF1381) How to enter Press the ESC , DISP then 3 keys, in that order. How to quit Press the I ESC I key. (DV 1394) Init OK AV 02 DV 01 Recorder GUID 00E0360004A00001 - DV GUID 0080880303480E96 VN VICTOR MN GR-D50K TM C3 TS 75 CT 32 WP 01 PS FF OS 00 CA A000002020 CV FF MD VTR (7 - DVdecode Yes LineSys 525-60 TC 00h20m35s02f RD 02 02 05 RT 10h34m50s ASPECT 4...

71s Aging Mode

If symptoms regarding recording playback of discs and or the HDD that your customer claimed are difficult to reproduce, they can be reproduced with a long-time test in Aging mode. Remote control unit for servicing (GGF1381) Remote control unit supplied with the unit (VXX2969) Commercially available, recordable DVD-R and DVD-RW discs When aging for the DVD-RW and HDD is executed, all recorded data on them will be erased. Commands from the remote control unit are accepted during Aging mode. If...

81 Front Section Front panel

Press to switch the recorder on into standby. Lights blue when the HDD is selected orange when DVD is selected. Press to switch between the hard disk drive (HDD) and DVD for recording and playback. 6 Front panel display and IR remote sensor Pull the cover down where indicated to access the front panel input jacks (audio, video and DV). Especially convenient for connecting camcorders and other portable equipment. Use to change channels, skip chapters tracks, etc. Press to start recording. Press...

Disc content format playback A compatibility

This recorder is compatible with a wide range of disc types (media) and formats. Playable discs will generally feature one of the following logos on the disc and or disc packaging. Note however that some disc types, such as recordable CD and DVD, may be in an unplayable format-see below for further compatibility information. DVD-Video DVD-R DVD-RW '-iudi ' digital audio digital audio Also compatible with KODAK Picture CD SS is a trademark of DVD Format Logo Licensing Corporation. is a trademark...

Front panel connections

On the right side of the front panel a flip-down cover hides more connections. A DV input i.LINK connector, suitable for connecting a DV camcorder. Audio video input (stereo analog audio composite and S-video video), especially suitable for camcorders, game consoles, portable audio, etc.

La73026av Scrb Assy Ic801

AIN1R AIN1L AIN2R AIN2L AIN3R AIN3L AIN4L AIN4R AIN5L AIN5R General purpose output Opencollector Video output terminal Push-pull output Low-impedance Video input terminal Sync-tip clamp Input Hi-impedance Control terminal for audio mute OPEN L FSS control terminal Output H, M, L 3 values with serial control Confirmed to IIC BUS. Data input terminal Confirmed to IIC BUS. Clock input terminal Video driver output terminal Push-pull output Low-impedance Audio output terminal Push-pull output...

Pmc002a8 Jckb Assy Ic101

Ccommunication strobe line with FL Driver WDT for detection of u-com in the state of out of control Handshaking of system control u-com communication Detection of S tereminal 3 connection Detection of S tereminal 2 connection Detection of S tereminal 1 connection CVBS, Y C mute signal for video driver IC Y Cb Cr mute signal for video driver IC CVBS or Y C selection of video selector Standby mode selection of video selector Letter-box output superimposed signal Through selection of AV.Link...

Rear panel connections

1 AV2(INPUT 1 DECODER) AV connector Audio video input output SCART-type AV connector for connecting to a VCR, or other equipment with a SCART connector. The input accepts video, S-video and RGB. See AV2 L1 In for how to set this up. Audio video output SCART-type AV connector for connecting to a TV or other equipment with a SCART connector. The video output is switchable between video, S-video and RGB. See page AV1 Out for how to set this up. A high-quality video output for connecting to a TV or...

Sg

The Windows Media logo printed on dicates that this recorder can playback Windows Media Audio WMA is an acronym for Windows Media Audio and refers to an audio compression technology developed by Microsoft Corporation. WMA content can be encoded by using Windows Media Player for Windows XP, Windows Media Player 9 or Windows Media Player 10 series. Microsoft, Windows Media, and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and or other...

717 Epg Service Mode Except DVR433H model

Reasons for the following malfunctions can be inferred by checking the conditions for obtaining the past EPG data EPG data cannot be obtained. 2 Some EPG data obtained are missing. Remote control unit for servicing (GGF1381) How to enter * Press the I ESC I, dTSP , I+10 I then 7 keys, in that order. Description of the mode 1. Summary screen The next download starting time for the EPG data is displayed. Next Data Download Time Starting time Duration Duration required for acquiring the EPG data...

Dvr530hav Dvr630hs

THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S). Please confirm 3rd & 4th alphabetical letters. When servicing this model, some service procedures may reset the customer settings to the factory default settings. Make sure to explain this to the customer. An HDD (Hard Disc Drive) is mounted in this product. The HDD is a precision instrument very vulnerable to shock and electrostatic charges. Please read 7.3 Cautions on Handling the HDD in this manual and exercise sufficient...

Diagnosis of MAIN Assy

D Press the 6 STANDBY ON button to turn on the power. (2 Press the OPEN CLOSE button to open the tray. (3 Remove the tray panel EB. < 4 Press the OPEN CLOSE button to close the tray. (5 Press the 6 STANDBY ON button to turn off the power. How to open the tray when the power cannot be turned on When the tray cannot be opened because the power cannot be turned on, it can be opened using the emergency disc ejection rod (GGF1529). (A long, thin rod about 1 mm in diameter can be used in place of...

5 Osd Filter Setting Sub screen

Purpose Depending on the monitor used, the character flicker on the OSD may stand out. If a system, such as charavter flicker, appears on the monitor, select the filter response. Remote control unit for servicing GGF1381 How to enter While the User Operation screen is displayed, press the ESC then DISP keys, then the DIG ANXI key four times, in that order. While subscreen 3 of the first screen is displayed, press the DIG ANA key. Select the setting from the key operation table. If a setting...

Pioneer Dvr-116 Service Manual

Pioneer Plc Schematics

FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE ONLY WITH SAME TYPE NO. 491.400PF002 FOR P202 MFD, BY LITTELFUSE INC. FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE ONLY WITH SAME TYPE NO. 491.630PF002 FOR P301 MFD, BY LITTELFUSE INC. FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE ONLY WITH SAME TYPE NO. 49101.6PF002 FOR P401 and P402 MFD, BY LITTELFUSE INC. Note The encircled numbers denote measuring point in the schematic diagram. 100 Coloro-bar AXP disc 1-23 1kHz, 60...

Cm0045af Main Assy Ic4201

Samsung 530h Copy Sda Scl Connection

CO III CO gt gt 55 55 555 5 gt gt gt 55 55 55 55 gt ccS gt gt 0 sgtisg gaS Q gt 3 iE ADC0 top reference electric potential ADC0 bottom reference electric potential PGA0 capacitor connection pin REF0-synctip ADC2 top reference electric potential ADC2 bottom reference electric potential PGA1 capacitor connection pin REF1-synctip ADC1 bottom reference electric potential ADC1 top reference electric potential ADC3 bottom reference electric potential ADC3 top reference electric potential Data for...

713 Firmware Downloading Method

When the main board is replaced, the firmware versions for the system control computer, drive, IR microcomputer and the TUFL microcomputer do not match, and operations of the unit may be destabilized. To match the versions for the above four, firmware downloading is necessary in the following two cases After the model setting When NG is displayed on the first screen version information, etc. of Service mode After changing MAIN Assy, JACB Assy or Drive Assy After changing HDD downloading the...

Atab Assy Others

CN12 40PATA CONECTOR CN11 40P CONNECTOR Q1202, Q1203 D1207 LED BLUE D1203 LED ORANGE CN1202 CONNECTOR POST CN1201 CONNECTOR gt IC4571 IC3203 IC3707 IC3706 IC4201 F3101, F3303-F3305, F4231 F4281, F4282, F5101 L1004-L1008, L1102, L5108 L4203 R8A34011BG TC74LCX541FTS1 TC7SAU04FU TC7SH08FUS1 C1320, C1321, C1328-C1331 C2501-C2505, C3004-C3006, C3101 C3104-C3106, C3113, C3202, C3203 C3206, C3209, C3217, C3309, C3312 C3401, C4244, C4249, C4251-C4256 C4261-C4263, C4265, C4291, C4501 C4504-C4507, C4516,...

2 Serial Download

Ufu Exe Pioneer Download

When the main board is replaced, the firmware versions for the system control computer, drive, and the TUFL microcomputer do not match, and operations of the unit may be destabilized. In such a case, the versions for the above three must be matched. 2. This method is used when disc downloading fails. In the serial download, the stored code are not downloaded to HDD. After serial downloading, be sure to do disc download. Connect the 232C I F jigs above way. 2 Turn on the PC and start the...

711 Model Type Setting

Pioneer Dvr530h

When the MAIN Assy and or TUJB Assy that are is commonly used with another model are is replaced, they it must recognize the model of this unit. Items to be set The model number, destination, and region No. must be set. Remote control unit for servicing GGF1381 Notes Once the setting has been made, it can never be changed. Be sure to make the setting correctly. As this setting resets the Assy s in question to the factory-preset status, it is recommended that you obtain After power on, the...

71 Diagnosis

Remote control unit for serving GGF1381 DVD Recorder Data Disc GGV1239 When repairing until June 2005, use the Disc GGV1179. Download disc Test disc GGV1025 DVD-RW Commercial goods Service Mode List 1. Setting type When rplacing MAIN ASSY or JACB ASSY. When CPRM ERROR is displayed on the display screen. After the MAIN ASSY, DRIVE ASSY or HDD replaced. After model setting After replacing MAIN ASSY, DRIVE ASSY, JACB ASSY . When NG is displayed for the version infomation in Service mode. 7.1.4...

List Of Assemblies

1 JAFL ASSY for Service VXX3005 1 KEYB ASSY for Service VXX3032 1 MAIN ASSY for Service VXX2997 KN301 WRAPPING TERMINAL VNE1948 1 SCRB ASSY for Service gt 1 POWER SUPPLY UNIT C930, C931 C906, C908 C925, C928 C907, C915 MSP3417G 2SA1576A 2SC4081 1SR154-400 CTF1399 LCYA100J2520 LCYA101J2520 VTL1081 CCSRCH101J50 CCSRCH220J50 CCSRCH560J50 CCSRCH561J50 CCSRCJ3R0C50 Q115, Q405 Q514, Q515 Q113, Q503, Q510 Q402, Q411 Q413 PMC002A8 2SA1036K 2SA1576A 2SB1238X 2SC2411K C149, C153, C154, C156, C160 C155,...

715 Service Mode

To be used to check the status of the product and to collect the information for failure diagnosis. The following information to be used for servicing is displayed Version, HDD information, etc. ATA ATAPI debug screen Writer information VR-recording-related error logs VR-playback-related error logs After entering any Service mode screen, to shift to another Service mode screen, first quit that Service mode screen then enter another Service mode screen. 1. Version information, etc. First screen...

Pcm1742ke Output Circuit

Korg Tr61 Power Supply Schematic Diagram

IC5101 UPD72852AGB-8EU IEEE1394 Physical IC NJ2 5I I l lt f h TPBN TPBP A_QND TP AN A_GND TPAP A_GND GND USB 5V USB 5V GND GND USB_DP2 GND USB_DM2 GND HDD DVD CN1202 DISC N VI S3B-PH-K-5 HDD DVD CN1202 DISC N VI S3B-PH-K-5 When ordering service parts, be sure to refer to EXPLODED VIEWS and PARTS LIST or PCB PARTS LIST. The gt mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. The...

Service Manual

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions. When replacing the lithium batteries, follow the note below. Dispose of the used battery promptly. Keep away from children. Do not disassemble and do not dispose of in The battery used in this device may present a fire or chemical hazard if mistreated. Do not recharge, disassemble, heat above...