Dsch3

Sony Dsc Repair Parts

File this supplement with the service manual. US Model Canadian Model AEP Model UK Model E Model Australian Model Hong Kong Model Chinese Model Korea Model Argentine Model Brazilian Model Japanese Model Tourist Model Change of Board's Suffix No. Note Please refer to Ver. 1.2 of SERVICE MANUAL 9-852-211-31 for the revision of accessories. Suffix No. of JK-348 flexible board has been changed from TT into T2 About suffix No. TT and T2 , there are no change of schematic diagram and printed wiring...

LinkElectrical Parts List [ accessories

Sony Dsc Cyber Shot Exploded View

-XX, -X mean standardized parts, so they may have some differences from the original one. Items marked are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. The mechanical parts with no reference number in the exploded views are not supplied. Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. All resistors are in ohms. METAL...

Link

Cn701 Sony

OVERALL BLOCK DIAGRAM 1 2 Number in parenthesis indicates the division number of schematic diagram where the component is located. LENS BLOCK VIDEO SIGNAL AUDIO SIGNAL VIDEO AUDIO SIGNAL VIDEO SIGNAL AUDIO SIGNAL VIDEO AUDIO SIGNAL BT001 ' LITHIUM j BATTERY FLASH V9, CONTROL, 6 CHARGE CONTROL CAM_13V CAM_-7.5V M_5.0V CAM_3.5V USB_3.1V D_3.0V A_3.0V DDR_1.8V D_1.8V D_1.5V D_1.2V BL_H EVER MS_VCC 4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

Info

179 Flexible Flash Sony Dsc

Printed wiring boards of the CD-708 flexible board and SY-185 board are not shown. Pages from 4-20 to 4-21 are not shown. JK-348 2 layers , MS-376 2 layers , PL-048 1 layer , FL-179 2 layers Note CN201 multi connector is not supplied, but this is included in the JK-348 flexible complete board. Note BT901 Is not included in the JK-348 flexible complete board. Note BT901 Is not included in the JK-348 flexible complete board. Note S101 is not supplied, but this is included in the ST-176 flexible...

HELP

Dsc Service Manual

Follow the disassembly in the numerical order given. Side Cover Lower -1 to -3 2 Cabinet Front 2-1 to 2-9 C EXPLODED VIEW HARDWARE LISI Short-circuit between the two points with the short jig about 10 seconds. Follow the disassembly in the numerical order given. Cabinet Rear -1 to -4 2 Cabinet Upper 2-1 to -10 Follow the disassembly in the numerical order given. Lens Block -1 to -4 2 SY-185 Board 2-1 to 2-5 LCD Module -1 to -7 EXPLODED VIEW HARDWARE LISI Follow the disassembly in the numerical...

C English i Japanese

A T m amp W , C tff . ssut h ffifisns. n T, D vtw g , c aw. l I lt gt roe- A sw. a r Sfi 6 a ft e-tf fisns. A tm gt 7i-7 hl C ti o 3 Write Enable Model ffVfc V'y amp o Cut and remove the part of gilt which comes off at the point. Be careful or some pieces of gilt may be left inside When installing a connector, don't press down at wire of connector. It is possible that a wire is snapped. Do not apply excessive load to the gilded flexible board. Make sure that the flat...

Sony Dsc-h3 Circuit

File this supplement with the service manual. US Model Canadian Model AEP Model UK Model E Model Australian Model Hong Kong Model Chinese Model Korea Model Argentine Model Brazilian Model Japanese Model Tourist Model Addition of Angular Velocity Sensor Type M Along with Type S, Type M is added at type of angular velocity sensor. As for the suffix No. of SY-185 board, 21 Type M in addition to TT Type S has been added. When the machine needs to be repaired, please refer to page 2 or 3 to...

Pl048 Flexible Board

LND101 LND102 LND103 LND104 LND105 LND106 LND107 LND108 LND109 LND110 LND111 LND112 LND113 LND114 LND115 LND116 LND117 LND118 LND119 LND120 LND121 LND122 LND123 LND124 LND125 LND126 -i gt MODE_DIAL2 -I2 gt MODE_DIAL1 I gt REG_GND_A -S gt BL_L -5 gt BL_H HE gt REG_GND_B -KEY_AD1 FLASH CONTROL, CHARGE CONTROL IC001 TPS65552RGTR FLASH CONTROL, CHARGE CONTROL IC001 TPS65552RGTR XX MARK NO MOUNT NO MARK REC PB MODE Note S101 is not supplied, but this is included in the ST-176 flexible complete...

English Japanese

HOW TO WRITE DATA TO INTERNAL MEMORY Usually, the camera has been set so as to disable the data writing from the PC to the internal memory of the camera. This setting must be changed temporarily when the data is to be written to the internal memory such as a case after the board replacement. To change the setting, use the write enable tool WriteEnableTool.exe. 1 Connect the PC to the camera USB mode Mass Storage , and switch the driver to the Sony Seus USB Driver. 2 Start the Write Enable...