1

1 Set the MODE selector to PLAY, then display the image to delete. 2 Select DELETE and then OK from the menu. The A (delete) indicator appears on the selected images and these images are deleted. If there are files on the Memory Stick with names having the same last 4 digits as the file name of the image to be deleted, these files are also deleted at the same time. 1 Set the MODE selector to PLAY, then display the INDEX screen. 2 Select DELETE and then ALL or SELECT from the menu. Select all...

2

1 Set the MODE selector to MOVIE or STILL. 2 Press MACRO so that the & (auto macro) indicator appears on the LCD screen. You can record a subject as close as about 4 inches (10 cm) from the lens surface with the zoom set all the way to the W side. (About 19 3 4 inches (50 cm) on the T side) Press MACRO again so that C& disappears from the LCD screen. You cannot record images in macro with the following PROGRAM AE modes. You cannot record images in macro when j i appears on the LCD screen....

20

Moving images with audio are recorded in MPEG format. To record moving images, slide the POWER switch to turn on the power and insert a Memory Stick. 2 Press the shutter button fully down. REC appears on the LCD screen, and the image and sound are recorded on the Memory Stick. If you press the shutter button once The image and sound are recorded for five seconds. You can change the recording time to 10 or 15 seconds with REC TIME SET in the menu settings (page 36). The image and sound are...

21 Adjusting Remote Commander

The adjusting remote commander is used for changing the calculation coefficient in signal processing, EVR data, etc. The adjusting remote commander performs bi-directional communication with the unit using the remote commander signal line (LANC). The resultant data of this bi-directional communication is written in the non-volatile memory. 1. Used the Adjusting Remote Commander 1) Connect the adjusting remote commander to the CN881 on the PD-137 board via CPC-9 jig (J-6082-393-C). 2) Adjust the...

21 Bt Lid Assembly Replacing Method

The shape of BT plate varies depending on the last code of BT holder assembly, as shown below. The BT lid assembly for service parts (X-3951-282-1) can be used only for the last code-3 of the BT holder assembly. For the last code-1 and -2 of the BT holder assembly, replace the BT holder assembly. BT plate of BT holder assembly having last code-1 and -2 BT plate of BT holder assembly having last code-3 Aligning with the rails of BT plate, slide new BT lid assembly in the direction of arrow . In...

212 Lens Block

Note 2 The old CPC-9 jig (Parts code J-6082-393-B) cannot be used, because it cannot operate the adjustment remote commander. It causes damage to the unit. Note 2 The old CPC-9 jig (Parts code J-6082-393-B) cannot be used, because it cannot operate the adjustment remote commander.

26 Lcd Module

SERVICE POSITION (LCD PANEL AND PD-137 BOARD) 2-7. ALUMINUM CABINET (REAR) ASSEMBLY REPLACING METHOD Peel off the light interception sheet (F). Between inner cabinet (rear) assembly and aluminum cabinet (rear) assembly Between inner cabinet (rear) assembly and aluminum cabinet (rear) assembly From the inner cabinet (rear) assembly, remove the aluminum cabinet (rear) assembly stuck with adhesive sheet (A) at two places.

3

1 Set the MODE selector to STILL. 2 Select FILE , REC MODE , and then TEXT from the menu. The number of images that you can record on a Memory Stick (8 MB) in TEXT mode If the subject is not evenly illuminated, you may be unable to record a clear image. Writing and reading data takes more time than in normal recording. Recording still images as uncompressed files (TIFF) This mode simultaneously records still images in both TIFF format (uncompressed) and JPEG format (compressed).

3 1

1 Set the MODE selector to STILL. 2 Select FILE , REC MODE , and then TIFF from the menu. The number of images that you can record on a Memory Stick (16 MB) in TIFF mode JPEG images are recorded in the image size selected by the IMAGE SIZE menu. TIFF images are recorded in 2048x1536 size other than when 2048 (3 2) is selected. Writing data takes more time than in normal recording. The supplied Memory Stick (8 MB) does not have sufficient capacity to record uncompressed images.

43

All capacitors are in iF unless otherwise noted. pF i iF. 50 V or less are not indicated except for electrolytics and tantalums. Chip resistors are 1 10 W unless otherwise noted. kQ 1000 Q, MQ 1000 kQ. Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. Some chip part will be indicated as follows. Constants of resistors, capacitors, ICs and etc with XX indicate that...

44

Adjusting the white balance (WHITE BALANCE) Normally the white balance is automatically adjusted. 1 Set the MODE selector to MOVIE or STILL. 2 Select CAMERA and then WHITE BALANCE from the menu. 3 Select the desired white balance setting. Places where the lighting condition changes quickly Under bright lighting such as photography studios Under sodium or mercury lamps Recording a sunrise sunset, night scene, neon signs, or fireworks

48

1 Set the MODE selector to PLAY. 3 Select FILE and then ROTATE from the menu. 4 Rotate the image clockwise V or counterclockwise -f, then select RETURN . You may not be able to rotate images recorded with other equipment. Also, when viewing images on a personal computer, the image rotation information may not be reflected depending on the application software. You cannot rotate protected or uncompressed images, Clip Motion images or images recorded in TEXT mode. Playing back the images in order...

5

Ht 0 10 i i 15Bflcooooq j2j B PROGRAM AE flash level flash mode indicator C White balance EV level sharpness indicator F AE lock indicator Focus lock indicator G Recording mode Clip Motion indicator I Self-diagnosis function recording time indicator K Remaining memory capacity indicator L Moving image VOICE recording time indicator They appear by pressing on the control button and disappear by pressing V of it. A Protect indicator B Print mark indicator C File name D Recording mode Clip Motion...

5 Adjustments

Discharging of the Flashlight Power Supply 5-4 5-6 4. Preparing the Flash Adjustment Box 5-7 1-2. Initialization of B, D, E, F, 7 Page Data 5-8 1-2-1. Initialization of D Page 5-8 2. Modification of D Page 3. D Page 1-2-2. Initialization of B, E, F, 7 Page Data 5-9 1. Initializing B, E, F, 7 Page Data 5-9 2. Modification of B, E, F, 7 Page Data 5-9 5. F Page 6. 7 Page Table 1. Video Sync Level 2. Video Burst Level 1. Flange Back Adjustment (Using the Minipattern...

52

Changing the recorded still image size (RESIZE) 1 Set the MODE selector to PLAY and display the image to resize. 2 Select TOOL and then RESIZE from the menu. 3 Select the desired image size. 2048x1536, 1600x1200, 1280x960, 640x480 The changed image is recorded, then the display returns to the image display before resizing. You cannot change the size of images recorded in TEXT mode, uncompressed images or Clip Motion images. When you change from a small size to a large size, the picture quality...

611 Upper Cabinet Section

Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. The mechanical parts with no reference number in the exploded views are not supplied. Accessories are given in the last of the electrical parts list. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifi s par une marque 0 sont critiquens pour la s curit ....

62 Electrical Parts List

Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. -XX and -X mean standardized parts, so they may have some difference from the original one. All resistors are in ohms. METAL Metal-film resistor. METAL OXIDE Metal oxide-film resistor. F nonflammable Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items....

64

D Image size indicator E Clip Motion indicator PROGRAM AE indicator White balance indicator Picture effect indicator Date time indicator H Battery usable time indicator (displayed only during charging) Number of recorded images Error display Err Some kind of misoperation has occurred. Check the self-diagnosis display on the LCD screen (page 64) and take the appropriate corrective action. LEH5 A problem has occurred with lens drive. Turn the camera on and off several times, and if the problem...

875305066

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifi s par une marque 0 sont critiques pour la s curit . Ne les remplacer que par une pi ce portant le num ro sp cifi . (Note 1) Be sure to read Precuations for Replacement of CCD Imager on page 4-8 when changing the CCD imager. (Note 2) Be sure to read 2-1. BT LID ASSEMBLY REPLACING METHOD on page 2-2 when changing the BT lid assy. The components...

Attachment Of Cpc9

Note 1 Don't use the 12 pin flexible board of CPC-9 jig It causes damage to the unit. Note 2 The old CPC-9 jig (Parts code J-6082-393-B) cannot be used, because it cannot operate the adjustment remote commander. CPC-9 jig (J-6082-393-C) (18p flexible board) Note 1 Don't use the 12 pin flexible board of CPC-9 jig It causes damage to the unit. Note 2 The old CPC-9 jig (Parts code J-6082-393-B) cannot be used, because it cannot operate the adjustment remote commander. CPC-9 jig (J-6082-393-C) (18p...

Cancel

* Displayed only in PLAY (single) mode. ** Displayed only in PLAY (INDEX) mode. 1 Set the MODE selector to MOVIE or STILL. 2 Select FILE and then IMAGE SIZE from the menu. 3 Select the desired image size. 2048x1536, 2048 (3 2)*, 1600x1200,1280x960, 640x480 * The image is recorded in 3 2 (horizontal vertical) size to match the printing paper size ratio of 3 2. The number of images or the time that you can record on a Memory Stick (8 MB) NORMAL . ** Numbers in parentheses indicate the maximum...

Dsc0ddddtif

Uncompressed image file recorded in TIFF mode (page 42) Moving image file recorded normally Audio file recorded in VOICE mode (page 41) The numerical portions of the following files are the same. A small-size image file recorded in E-MAIL mode and its corresponding image file An uncompressed image file recorded in TIFF mode and its corresponding image file An audio file recorded in VOICE mode and its corresponding image file An image file recorded in TEXT mode and its corresponding index image...

E

Your camera has a self-diagnosis display. This function displays the camera condition on the LCD screen with a combination of a letter and four digits of numbers. If this occurs, check the following code chart. The code informs you of the camera's current condition. The last two digits (indicated by ) will differ depending on the state of the camera. You can reverse the camera malfunction yourself. Contact your Sony dealer or local authorized Sony service facility. You can reverse the camera...

Ahx

Y level data 64 to 98 (Note 4) R-Y level data FA to FF or 00 to 06 (Note 5) B-Y level data FA to FF or 00 to 06 (Note 5) A D integral value data 0020 or more (Note 6) Note 1 Perform Flange Back Adjustment, Light Level Adjustment and Auto White Balance Adjustment before this adjustment. Perform this adjustment in the Flash adjustment box. Refer to 4. Preparing the Flash adjustment box. (See page 5-7) Note 4 Displayed data of page F, address 64, of the adjusting remote commander. Note 5 The right...

Egq

Note 1 Perform Auto White Balance Standard Data Input and Auto White Balance Adjustment before this adjustment. Note 2 Check that the data of page 6, address 02 is 00. If not, turn the power of unit OFF ON. Note 1 Perform Auto White Balance Standard Data Input and Auto White Balance Adjustment before this adjustment. Note 2 Check that the data of page 6, address 02 is 00. If not, turn the power of unit OFF ON.

Kqx

R ratio 28E0 to 2A20 B ratio 5C60 to 5DA0 Note 1 Perform Auto White Balance Reference Data Input before this adjustment. Note 2 Check that the data of page 6, address 02 is 00. If not, turn the power of unit OFF ON. Note 3 The right four digits of the page 1 displayed data of the adjusting remote commander. 1 XX XX Note 4 Refer to Picture Frame Setting for XH, XL, YH and YL.

Xwn

Note 1 Perform Auto White Balance Reference Data Input before this adjustment. Note 2 Check that the data of page 6, address 02 is 00. If not, turn the power of unit OFF ON. Note 1 Perform Auto White Balance Reference Data Input before this adjustment. Note 2 Check that the data of page 6, address 02 is 00. If not, turn the power of unit OFF ON.

Hold

Recording a single-colored subject or background Adjusts the white balance automatically Select AUTO when recording under fluorescent lighting. Recording the date and time on the still image (DATE TIME) 1 Set the MODE selector to STILL. 2 Select EFFECT and then DATE TIME from the menu. 3 Select the date and time setting. The date, hour and minutes are imposed onto the image.

Info

When you first use your camera, set the date and time. If these are not set, the CLOCK SET screen appears whenever you turn on your camera for recording. 1 Slide the POWER switch to turn on the power. 2 Press on the control button. The menu bar appears on the LCD screen. 3 Select SETUP with on the control button, then press the center . 1 Open the jack cover and connect the DC connecting cable to the DC IN jack of your camera with the mark facing up. 2 Connect the power cord (mains lead) to the...

J9

Note 1 For details of how remove the cabinet and boards, refer to 2. DISASSEMBLY. Note 2 When performing only the adjustments, the lens block and boards need not be disassemble. 1) Connect the equipment for adjustments according to Fig. 5-15. 2) Connect the Adjusting remote commander to PD-137 board CN881 via CPC-9 jig (J-6082-393-C). (See Fig. 5-1-3) Note 3 Setting the Forced STILL mode power ON Mode 1) Select page 0, address 01, and set data 01. 2) Select page D, address 10, set data 01, and...

Memory Stick Error

When failed in the focus and zoom initialization. Checking of flash unit or replacement of flash unit. Abnormality when flash is being charged. *i Note The error code is cleared if the battery is removed, except defective flash, unit. *1 When the flash charging failed, Page D, Address 67, Data 04 are written. After repair, be sure to write Page D, Address 67, Data 00.

Notice For The Customers In The United Kingdom

A moulded plug complying with BS 1363 is fitted to this equipment for your safety and convenience. Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse approved by ASTA or BSI to BS 1362, (i.e. marked with or mark) must be used. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service...

O X X

Cut and remove the part of gilt which comes off at the point. (Be careful or some pieces of gilt may be left inside) Discharging of the ST-62 board's charging capacitor (C1003) The charging capacitor (C1003) of the ST-62 board is charged up to the maximum 300 V potential. There is a danger of electric shock by this high voltage when the battery is handled by hand. The electric shock is caused by the charged voltage which is kept without discharging when the main power of the unit is simply...

Pc

(The same model of the same destination) After the EVR data is saved and downloaded, check the respective items of the EVR data. (Refer to page 5-2 for the items to be checked. 1-1. Adjusting items when replacing main parts and boards When replacing main parts and boards, adjust the items indicated by 0 in the following table. CA-66 board IC103 (S H, AGC, A D,Timing generator) PD-137 board IC804 (LCD Timing generator)

R

2 Press and hold the shutter button halfway down and check the image. While the AE lock indicator Z (green) is flashing rapidly, the image freezes momentarily, but is not yet recorded. When the camera finishes the automatic adjustments*, the AE lock indicator Z stops flashing rapidly and lights up.** The camera is ready for recording. To cancel the recording, release the shutter button. 3 Press the shutter button fully down. The shutter sounds and the image is recorded on the Memory Stick. When...

Replacing Method

Peel off the light interception sheet (F). Between inner cabinet (rear) assembly and aluminum cabinet (rear) assembly Between inner cabinet (rear) assembly and aluminum cabinet (rear) assembly From the aluminum cabinet (rear) assembly, remove the inner cabinet (rear) assembly stuck with adhesive sheet (A) at two places. Pull off the forcibly fitted parallel pin (dia. 1.6 x 5) in the direction of arrow . Pull the jack cover off the inner cabinet (rear). Insert the jack cover into new inner...

Specifications

(39 - 117 mm when converted into a 35 mm still camera) F 2.8 - 5.3 Exposure control Automatic exposure White balance Automatic, Indoor, Outdoor, Hold Movie MPEG1 Still JPEG, GIF (in TEXT mode, Clip Motion ), TIFF Audio with still image MPEG1 (Monaural) Recording medium Memory Stick Flash W side 1 5 8 feet to 7 1 2 feet (0.5 m to 2.3 m) T side 1 5 8 feet to 3 7 8 feet (0.5 m to 1.2 m) Video 1 Vp-p, 75 Q, unbalanced, sync negative Audio 327 mV (at a 47 kQ load) 1.5 type TFT (Thin Film Transistor...

M M

Select II (pause) on the LCD screen with V V b B on the control button, then press the center . Viewing images using a personal computer You can view data recorded with your camera on a personal computer and attach it to e-mail. This section describes the method for installing the USB driver and viewing images on a personal computer. Be sure to also see the operation manuals for your personal computer and application software. Data recorded with your camera is stored in the following formats....

Type St

6082 393 Sony

Note 1 Don't use the 12 pin flexible board of CPC-9 jig. It causes damage to the unit. Note 2 The old CPC-9 jig Parts code J-6082-393-B cannot be used, because it cannot operate the adjustment remote commander. Description on Self-diagnosis Display The camera has a self-diagnosis display. This function displays the camera condition with five-digits a combination of a letter and figures on the LCD screen. If this occurs check the following code chart. The five-digits display informs you of the...

143574121 141982811

TRANSFORMER, DC-DC CONVERTER COIL, TRIGGER Note Resistor is mounted to the location where FB052 is printed. 5002 1-771-138-61 SWITCH, KEY BOARD FLASH 5003 1-771-138-61 SWITCH, KEY BOARD MACRO 5005 1-771-138-61 SWITCH, KEY BOARD VOLUME 5006 1-771-138-61 SWITCH, KEY BOARD LCD ON OFF 5007 1-771-138-61 SWITCH, KEY BOARD VOLUME - 5008 1-771-138-61 SWITCH, KEY BOARD PROGRAM AE