00

Note 1 For the bit values, refer to 5-2. SERVICE MODE, 2-3. 2. Bit value discrimination. Note 1 For the bit values, refer to 5-2. SERVICE MODE, 2-3. 2. Bit value discrimination. Select page 2, address 00 and set data 29. Select page 2, address 01 and set data 29. Select page 2, address 0C, set the bit value of bit 1 is 1. Select page 2, address 04 and set data 04. Set the adjusting remote commander to normal LANC, and the power will be turned off and on automatically. Note 3 Repeat the Data...

04

Before setting the data, select page 0, address 01, and set data 01. For page D, the data set is recorded in the non-volatile memory by pressing the PAUSE button of the adjusting remote commander. In this case, take note that the test mode will not be exited even when the main power is turned off. After completing adjustments repairs, be sure to return the data of this address to 00, and press the PAUSE button of the adjusting remote commander. Select page 0, address 01, and set data 00. Bit...

05

Precautions for Replacement of CCD Imager The CD-391 board mounted as a repair part is not equipped with a CCD imager. When replacing this board, remove the CCD imager from the old one and mount it onto the new one. If the CCD imager has been replaced, carry out all the adjustments for the camera section. As the CCD imager may be damaged by static electricity from its structure, handle it carefully like for the MOS IC. In addition, ensure that the receiver is not covered with dusts nor exposed...

1

Preparations Before Adjustment 5-3 1-2. 1-3. Discharging of the Flashlight Power Supply 5-4 1-4. 5-6 4. Preparing the Flash Adjustment Box 5-7 Initialization of A, B, D, E, F, 7, 9 Page Data 5-8 Initialization of A, D Page Data 5-8 Initializing A, D Page Data 5-8 Modification of A, D Page Data 5-8 Initialization of B, E, F, 7, 9 Page Data 5-9

104

Focus preset value (60) K EV adjustment indicator (56) L Macro (DSC-P71) (28) M Self-timer indicator (29) N Menu Guide menu (55) When you press the MENU button, Menu Guide menu is toggled between display don't display is not displayed on the menu of the DSC-P31 (page 61). The page numbers in parentheses indicate the location of additional important information. For still image playback For movie playback

128mb

When the shooting mode is normal For the number of images that can be saved in other modes, see page 91. When the shooting mode is normal For the number of images that can be saved in other modes, see page 91. The image size is the screen size used when viewing the images on a personal computer. When the images are viewed on the LCD screen of the camera, they all look the same size. Number of shooting images can differ from these values according to shooting conditions. The image size value...

14

Charging the Nickel-Metal Hydride batteries If the poles of the Nickel-Metal Hydride batteries are dirty, the batteries may not charge properly. Occasionally clean the poles of the batteries and the terminals of the charger by wiping them with a dry cloth. At the time of purchase, or when the NickelMetal Hydride batteries haven't been used for a long time, they may not fully charge. This is typical of this type of battery, and is not a malfunction. If this happens, repeatedly using up the...

14 Camera System Adjustments

Before perform the camera system adjustments, check that the specified values of VIDEO SYSTEM ADJUSTMENTS are satisfied. Note For CAMERA SYSTEM ADJUSTMENTS, perform in order of item numbers. Data setting during camera system adjustments Perform the following data setting before the camera system adjustments. It is not necessary to perform the following data setting everytime when you perform some items of camera system adjustments continuously unless the power is turned off. Only when the power...

15 Lcd System Adjustments

Before perform the camera system adjustments, check that the specified values of VIDEO SYSTEM ADJUSTMENTS are satisfied. Note 1 Taken an extreme care not to destroy the liquid crystal display module by static electricity when replacing it. Note 2 Set the LCD BRIGHTENSS (SET UP setting) to the NORMAL. Most of the measuring points for adjusting the LCD system are concentrated in CN 903 of the PK-064 board. Connect the Measuring Instruments via the CPC-9 jig (J-6082- The following table shows the...

182400981

CORD, CONNECTION (AV CONNECTING 1.5m) 1-823-932-11 CORD, CONNECTION (USB 5P) 3-065-665-01 MANUAL, INSTRUCTION (for SAFETY) 3-072-414-01 SPVD-008 (CD-ROM) (EXCEPT J, US, CND) 3-072-654-01 SPVD-008 (I) (CD-ROM) (J, US, CND) 3-072-705-01 REGISTRATION (CD-ROM) (V5.1 I-V2.0) (J) 3-074-351-01 MANUAL, INSTRUCTION (JAPANESE) (J) 3-074-351-11 MANUAL, INSTRUCTION (ENGLISH) (US, CND, AEP, UK, E, HK, AUS, CH, JE) 3-074-351-21 MANUAL, INSTRUCTION (FRENCH, GERMAN) 3-074-351-41 MANUAL, INSTRUCTION (DUTCH,...

21 Adjusting Remote Commander

The adjusting remote commander is used for changing the calculation coefficient in signal processing, EVR data, etc. The adjusting remote commander performs bi-directional communication with the unit using the remote commander signal line (LANC). The resultant data of this bi-directional communication is written in the non-volatile memory. 1. Used the Adjusting Remote Commander 1) Connect the adjusting remote commander to the CN903 on the PK-062 Board via CPC-9 jig (J-6082-393-C). 2) Set the...

210 Jk223 Board

SERVICE POSITION (SY-075 BOARD SIDE A) CPC-9 jig (J-6082-393-C) (Note 1, 2) Note 1 Don't use the 12 pin flexible board of CPC-9 jig. It causes damage to the unit. Note 2 The old CPC-9 jig (Parts code J-6082-393-B) Cannot be used, because it cannot operate the adjustment remote commander.

22

Inserting and removing a Memory Stick , Open the Memory Stick cover. Slide the cover in the direction of the arrow to open it. , Insert the Memory Stick. Holding the Memory Stick as shown in the illustration, insert it all the way in until it clicks. Whenever you insert a Memory Stick, push it all the way in until it clicks. If you do not insert it correctly, a message such as MEMORY STICK ERROR will be displayed on the LCD screen. , Close the Memory Stick cover. To remove a Memory Stick Open...

24

You can choose image size (number of pixels) and image quality (compression ratio) based on the kind of images you want to shoot. The larger you make the image size and the higher you make the image quality, the better your image, but also the larger the amount of data needed to preserve your image. This means you can save fewer images in your Memory Stick. Choose an image size and quality level appropriate for the kind of images you want to shoot. You can resize the images later (Resize...

24 V

AC-LS1 AC power adaptor (not suppled), 4.2 V Power consumption (when recording) 1.7W 0 to + 40 C (32 to +104 F) Storage temperature range -20 to + 60 C (-4 to + 140 F) Dimensions 106 x 58 x 39.5mm (4 1 4 x Q 3 8 x 1 9 16 inches) (W H D, protruding portions not included) 231 g (8 oz) (camera, two batteries, Memory Stick and wrist strap included) AC 100 to 240V 50 60Hz 2.2 W Output voltage inches) (W H D) Mass Approx. 70g (2 oz) AC-LS1 AC power adaptor (not supplied) AC 100 - 240 V, 50 60 Hz...

255

Note ( ) indicate the adjusting remote control unit display. Note ( ) indicate the adjusting remote control unit display. (Example) In the case that the adjusting remote control unit display are BD (bd). As the upper digit of the hexadecimal notation is B (b), and the lower digit is D (d), the intersection 189 of the and 2 in the above table is the decimal notation to be calculated. 2-3. SERVICE MODE 1. Setting the Test Mode

26

Checking the last shot image (Quick Review) A beeping sound is heard, the shooting is completed, and the still image is saved in the Memory Stick. When the Recording lamp goes out, you can shoot the next image. When you are shooting with the battery, if no tasks are performed for a while* with the camera turned on, power is automatically shut off to preserve battery power (page 20). * When POWER SAVE is set to ON approximately 90 seconds When POWER SAVE is set to OFF approximately 3 minutes...

29

Note 1 Fixed data-1 Initialized data. (Refer to 1. Initializing the A Page Data) Note 2 Fixed data-2 Modified data. (Refer to 2. Modification of A Page Data) (Refer to 1. Initializing the A Page Data) Note 2 Fixed data-2 Modified data. (Refer to 2. Modification of A Page Data)

3

, Turn the Mode dial to O, and press ( ) on the control button. CD (Macro) will appear on the LCD screen. If the menu is currently displayed, press the MENU button first and the menu will disappear. You can perform this operation even when the Mode dial is set to SCN (other than Landscape mode) (page 34), or H H , Center the subject in the frame, and shoot the image. Press (CEO on the control button one more time. disappears from the LCD screen. Use the LCD screen to shoot when using the Macro...

30

To reduce red-eye when recording live subjects When the flash begins to strobe before the image is shot, the red-eye phenomenon is reduced. In SET UP, set RED EYE REDUCTION to ON (page 97). o will be displayed on the LCD screen. The amount of red-eye reduction possible varies according to the individual. In addition, the distance to the subject, and whether or not the subject has seen the flash begin to strobe may also reduce the effectiveness of the red-eye reduction process. This is...

34

, Select SCN using b B on the control button. I 0 (Spot light-metering) is not displayed on the menu of the DSC-P31 (page 61). , Select the desired mode using V V on the control button. The mode will be set to your choice. When the setting is completed, press the MENU button. The menu disappears from the screen. When you cancel Scene selection, set the mode dial to something other than SCN. The settings made here will be saved even when the power is turned off. In Twilight or Twilight portrait...

36

, Select Still Image using b B on the control button. b Displays the previous image. B Displays the next image. The display switches to the Index (9 images) screen. To display the previous (next) Index screen Press V V b B on the control button to move the yellow frame up down left right. , Press the Zoom W button once more. The display switches to the Index (3 images) screen. When you press V V on the control button, the remaining image information is displayed. To display the previous (next)...

38

If you want to view the playback picture on a TV, you need a TV having a video input jack and a video connecting cable. The color system of the TV must be the same as that of your digital still camera. Check the following list Bahama Islands, Bolivia, Canada, Central America, Chile, Columbia, Ecuador, Jamaica, Japan, Korea, Mexico, Peru, Surinam, Taiwan, the Philippines, the U.S.A., Venezuela, etc. Australia, Austria, Belgium, China, Czech Republic, Denmark, Finland, Germany, Holland, Hong...

40

Deleting on the Index (3 images) screen , Select the image you want to delete using A T b B on the control button then press the center Z. The mr mark appears next to the selected images. At this point, the images have not yet been deleted. Put a flj mark next to all of the images you want to delete. To cancel your selection, press the center one more time. , Press the MENU button, select OK using b B on the control button, then press the center When MEMORY STICK ACCESS disappears, the images...

42

, Insert the Memory Stick you want to format into the camera. Turn the mode dial to SET UP, and turn on the power. 1 The term formatting means preparing a Memory Stick to record images this process is also called initialization. The Memory Stick provided with this camera, and those available commercially, are already formatted, and can be used immediately. When you format a Memory Stick, be aware that all of the images in the Memory Stick will be permanently deleted.

44

Step O may be unnecessary depending on your OS. After you complete the installation of the USB driver, step O is unnecessary. OS Microsoft Windows 98, Windows 98SE, Windows 2000 Professional, Windows Millennium Edition, Windows XP Home Edition, or Windows XP Professional An OS installed at the factory (not upgraded) is required for correct operations. We cannot guarantee operations for operating systems not listed above. CPU MMX Pentium 200 MHz or faster USB connector OS Mac OS 8.5.1, 8.6,...

48

When a removable disk icon is not shown 1 Right-click My Computer, then click Property. The System Property window appears. 2 Confirm if other devices are already installed. Click Device Manager. Double-click fl Other Devices. (D Confirm if there is a FSlSony DSC or Sony Handycam with a mark. 3 If you find either of the devices above, follow the steps below to delete them. Sony Handycam. 2 Click Delete. The Device deletion confirmation window appears. Click OK. Try the USB driver installation...

52

, Double-click My Documents on the desktop. The My Documents folder opens. , Double-click the desired image file. This section describes the steps followed for copying images to the My Documents folder on page 48. When using Windows XP, click Start t My You can use the PIXELA ImageMixer for Sony software to view images on your computer. For details, see the software's help

5258

1-771-138-82 SWITCH, KEY BOARD (ZOOM (W)) 1-786-039-21 SWITCH, TACTILE (CONTROL) 1-771-138-82 SWITCH, KEY BOARD (ZOOM (T)) 1-771-138-82 SWITCH, KEY BOARD (MENU) 1-771-138-82 SWITCH, KEY BOARD (DISPLAY LCD) 1-771-731-21 SWITCH, SLIDE (POWER SAVE) 1-786-342-11 ROTARY, ROTARY SLIDE SWITCH 1-786-227-21 SWITCH, TACTILE (RESET) 1-795-244-11 VIBRATOR, CERAMIC (10MHZ) 1-767-994-42 VIBRATOR, CRYSTAL (32.768kHz)

58

Shooting with the AF lock using Center AF If it is difficult to focus because the subject is not in the center of the frame, you can focus in this situation using the AF range finder. For example, when you are shooting two human subjects, and there is a gap between them, the camera may focus on the background visible in the gap. In a case like this, use AF lock to ensure the subjects are in correct focus. When you are using AF lock, you can capture an image with the correct focus even if the...

5b

Initialization of B, E, F, 7, 9 Page Data 1. Initializing B, E, F, 7, 9 Page Data Note If the B, E, F, 7, 9 Page data has been initialized, Modification of B, E, F, 7, 9 Page Data and following adjustments need to be performed again. 1) Modification of B, E, F, 7, 9 page data 2. Modification of B, E, F, 7, 9 Page Data If the B, E, F, 7, 9 Page data has been initialized, change the data of the Fixed data-2 address shown in the following tables by manual input. 1) Before changing the data,...

6

Press the MENU button again and select using b B on the control button, select OFF then using V V. The Spot light-metering aiming point disappears, and the camera returns to normal lightmetering. b Press B ( ) on the control button to turn Spot lightmetering on. The Spot light-metering aiming point is displayed. C Aim the Spot light-metering aiming point at the spot you want to shoot, then shoot your image. Press B ( 1) on the control button to turn Spot light-metering off. The Spot...

60

C Select 9 using b B, then select the distance to the subject using A V. You can select from the following distance settings. 0.5m, 1.0m, 3.0m, 7.0m, (unlimited distance) Press the MENU button again, select 9, then select MULTI AF or CENTER (Spot light-metering) is not displayed on the menu of the DSC-P31 (page 61). The focus distance settings include a small margin of error. Use them as guidelines only. If you point the lens up or down, the error increases (DSC-P71 only). You can add special...

61 Exploded Views

-XX and -X mean standardized parts, so they may have some difference from the original one. Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. DSC-P31M is the same as DSC-P31 (US model) except packing materials. Therefore, information about DSC-P31 (US model) in the text is applied. The mechanical parts with no reference number in the exploded views are not supplied. Accessories are given in the last of...

62

In MOVING IMAGE in SET UP, select CLIP MOTION (pages 55, 97). Control button Q Turn the Mode dial to gj. b Press the MENU button. C Select (IMAGE SIZE) using b B, and select the desired mode useing V V. Press the shutter once to shoot the next frame, then repeat this operation until you have shot the desired number of frames. All of the frames will be saved in the Memory Stick. If you do not complete Step 0, the image will not be saved in the Memory Stick. Up to that point, the image is saved...

62 Electrical Parts List

Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. -XX and -X mean standardized parts, so they may have some difference from the original one. All resistors are in ohms. METAL Metal-film resistor. METAL OXIDE Metal oxide-film resistor. F nonflammable Abbreviation AUS Australian model CH Chinese model CND Canadian model HK Hong Kong model Items marked * are not stocked since they are seldom required...

64

Q Turn the Mode dial to gig. b Press the MENU button. C Select usi ng b B, then select the desired between-frame interval using V V. You can choose the between-frame interval from among the following. NTSC 1 7.5 sec., 1 15 sec., 1 30 sec. PAL 1 6.3 sec., 1 12.5 sec., 1 25 sec. (For information on NTSC PAL, see page 95.) 16 frames will be recorded as one image (image size 1280 x 960). When you play back images recorded with this camera in Multi Burst mode, the 16 frames will be played back in...

66

Recording an enlarged image - Trimming Q After you have viewed an image using playback zoom, press the MENU button. b Select TRIMMING using , then press the center . 0 Select the image size using A V, then press the center . The image will be recorded, and the screen image will return to the size it was before enlargement. The trimmed image will be recorded as the newest file, and the original image will be retained. The trimmed image may suffer some deterioration in image quality You cannot...

68

To prevent accidental erasure of an important image, you can protect it. b Display the image you want to protect using b B. 0 Select PROTECT using b B, then press the center z. The image currently being displayed is now protected, and a (Protect) mark is shown on the screen.

7

A Recording mode indicator (74) B Remaining battery indicator display (16) C White balance indicator (57) D Picture effect indicator (60) E Spot light-metering aiming point (61) F AF range finder (58) G Image size indicator (74) H Recording time remaining indicator (Maximum recording time) indicator (18) Self-diagnostics display (90) I Remaining Memory Stick capacity indicator (25)

70

To remove protection from previously protected images In Step Q, select the image from which you want to remove protection, and press the center Z. To remove protection from all of your images, repeat this process for each of them. You can change the size of your images, and record them as new files. You can change your images to the following sizes. 2048x1536 (DSC-P71 only), 1600x1200, 1280x960, 640x480 After the resizing is finished, the original image is retained. Select RESIZE using b B,...

72

F To print other images, repeat Step 5 for each of them. h Select OK using B, then press the center z. The setting of the M (Print) mark is completed. To delete a Bf (Print) mark, select an image using the control button, and press the center z. To delete the Print marks attached to all of your images In Step Q, select ALL, then press the center z. Next, select OFF, and press the center z. In Step Q, select CANCEL, or select EXIT in Step , then press the center z. Q Turn the mode dial to ,...

76

F Repeat Step 5 of the procedure to delete other images. h Select OK using b B and press the center z. The image is deleted when the MEMORY STICK ACCESS message disappears. Select CANCEL in Step 0, and press the center z. Select ALL in Step Q, and press the center z. To cancel the deletion, select CANCEL using b B and press the center Deleting on the Index (3 images) screen Q Turn the Mode dial to and press the W zoom button twice to display an Index (3 images) screen. b Show the desired image...

78

Press the center Z at the desired cutting point. When you want to adjust the cutting point, use -bll IC (frame forward rewind) and adjust the cutting point using b B. If you want to change the cutting point, select CANCEL. The playback of the movie starts again. f When you have decided on a cutting point, select OK using v V, and press the center z. Q Select OK using and press the center z. Select EXIT in Step Q. The movie Files not long enough to cut You cannot restore files once you cut them....

80

The Close the Scanner and Camera Wizard screen is displayed. The Wizard screen closes. If you want to copy other images, disconnect the USB cable, and then start over again from Step Q. 1 Double-click the newly recognized icon on the desktop. The contents of the Memory Stick inserted into your camera appear. 2 Double-click MSSONY. 3 Double-click MOML0001. 4 Drag and drop the movie files to the hard disk icon. The movie files are copied to your hard disk. To...

82

The LCD screen does not light when the power is turned on. The power was turned off with the LCD screen set to OFF the last time the camera was used. The subject is not visible on the LCD screen. The mode dial is not set to O or SCN, or . p Set it to or SCN, or U (pages 26, 74). Scene selection is set to the Landscape mode. p Set the macro recording mode (DSC-P71 only) when you shoot a subject that is within 50 cm (19 inches) from the lens. Make sure to place the lens farther away from the...

84

Images are coarse right after being played back. The images cannot be played back on a TV. The VIDEO OUT setting for your camera in SET UP is incorrect. The connection is not correct. pSet it to NTSC or PAL (pages 55, 98). p Check the connection (page 38). The images cannot be played back on a personal computer.

9

Note 1 Fixed data-1 Initialized data. (Refer to 1. Initializing B, E, F, 7, 9 Page Data) Note 2 Fixed data-2 Modified data. (Refer to 2. Modification of B, E, F, 7, 9 Page Data) Note 1 Fixed data-1 Initialized data. (Refer to 1. Initializing the B, E, F, 7, 9 Page Data) Note 2 Fixed data-2 Modified data. (Refer to 2. Modification of B, E, F, 7, 9 Page Data)

92

When the Mode dial is set to , SCN. (continued) Records images with fine image quality mode. Records images in the standard image quality mode (page 24). - Records a small-size (320x240) JPEG file in addition to the selected image size (page 65). - Records an image using the normal recording mode.

96

The setup screen appears. Factory settings are indicated with . When shooting movies Clip Motion, the date and time cannot be inserted in the image. Also, the date and time will not be displayed when shooting. The date and time of playback will be displayed when the image is played back.

98

Clean the screen surface with an LCD cleaning kit (not supplied) to remove fingerprints, dust, etc. Wipe the lens with a soft cloth to remove fingerprints, dust, etc. Clean the camera surface with a soft cloth slightly moistened with water, then wipe the surface with a dry cloth. Do not use any type of solvent such as thinner, alcohol or benzine as this may damage the finish or the casing. The camera is designed for use within a temperature range of 0 - 40 (32 F and 104 F). Shooting in...

A

CAUTION TO REDUCE THE RISK CF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK . NO USEH43EnVICEABLE PART INSIDE. REFER SERVICING TO QUAUFIED SERVICE PI This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature...

A9

Note 1 Fixed data-1 Initialized data. (Refer to 1. Initializing the D Page Data) Note 2 Fixed data-2 Modified data. (Refer to 2. Modification of D Page Data) (Refer to 1. Initializing the D Page Data) Note 2 Fixed data-2 Modified data. (Refer to 2. Modification of D Page Data)

Bs

(Menu on) (A T b B ) (20) (Menu off) ( 7 ) (27, 29, 30, 61) J LCD screen K DC IN jack cover (19) D MENU button (24) E Jack cover F USB jack (47) G VIDEO OUT jack (38) To shoot still images H To view or edit images id To shoot movies Clip Motion images Multi Burst mode images SET UP To set the SET UP items SCN To shoot in the SCENE SELECTION mode M Zoom button (for shooting) (28) Index button (for viewing) (37) N Wrist strap hook O Open lever P Battery cover Q Memory Stick cover R Access lamp...

C

Do not remove the Memory Stick while reading or writing data. Data may be damaged in a location subject to the effects of static electricity or noise. Do not attach any other material than the supplied label on the labeling position. When you carry or store the Memory Stick, put it in the case supplied with it. Do not touch the terminals of a Memory Stick with your hand or a metal object. Do not strike, bend or drop a Memory Stick. Do not disassemble or modify a Memory Stick. Do not expose the...

C108

SY-075 (CAMERA DSP, VIDEO MEMORY, LENS DRIVE, SH DSP, FLASH MEMORY, CLOCK GENERATOR, DC DC CONVERTER) SY-075 board is eight-layer print board. However, the patterns of layers 2 to 7 have not been included in the diagram. There are a few cases that the part isn't mounted in this model is printed on this diagram. See page 4-61 for printed parts location.

C4

* R260 B-3 R304 C-3 R306 C-5 R309 C-5 R310 C-5 R311 C-5 R312 D-4 * R317 C-5 R318 D-5 R319 D-5 * R328 C-5 R505 A-3 R506 C-3 R507 A-3 R517 A-3 R520 C-3 R521 B-2 R522 C-2 R525 C-2 R526 C-2 R527 C-2 R528 C-2 R533 B-2 R536 B-2 R540 B-2 R548 B-2 R549 B-2 R554 A-3 R557 A-3 R563 A-3 R564 A-3 R568 A-3 R569 A-3 R573 A-3 * R579 A-4 R582 B-2 R583 B-2 R586 A-3 * R711 B-5 R783 B-4 R785 B-4

Camera

Moving image date time digital zoom red eye reduction af illuminator b Select the setting item you want to change using A T b B on the control button. The frame of the item you select will turn yellow. C Press the center Z on the control button to enter the setting. On the DSC-P31, the DIGITAL ZOOM (page 28) and POWER SAVE (page 16) items are not displayed. To turn off the SET UP screen display Turn the Mode dial to anything other than SET UP.

Caution

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used...

Ccc1 2cc2 7 4 1c

Press b B while playing back a movie. To return to the normal playback, press the center z. Movies with the image size 320 (HQX) appear on the full screen. Messages displayed on the screen while movies are being played back Each time you press the DISPLAY LCD ON OFF button, the status of the LCD screen changes as follows Display OFF LCD OFF Display ON. See page 105 for a detailed description of the indicated items. The procedure for viewing movies on a TV is the same as that for viewing still...

Ceramic Chip

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifi s par une marque 0 sont critiques pour la s curit . Ne les remplacer que par une pi ce portant le num ro sp cifi . The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifi s par une marque 0 sont critiques pour la s curit . Ne les remplacer que par...

Ch109

SY-075 (CAMERA DSP, VIDEO MEMORY, LENS DRIVE, SH DSP, FLASH MEMORY, CLOCK GENERATOR, DC DC CONVERTER) SY-075 board is eight-layer print board. However, the patterns of layers 2 to 7 have not been included in the diagram. There are a few cases that the part isn't mounted in this model is printed on this diagram. See page 23 for printed parts location.

Clock

, Choose the year, month, day, hour, and minute items using b B. A will be shown above, and a V will be shown below the item currently selected to be set. , Set the desired numerical value using V V on the control button, then press the center After setting the current numerical value, move to the next item. Repeat the above process until all of the items have been set. If you choose D M Y in Step 3, use the 24 hour clock display. Choose OK using the B on the control button, and then press the...

D4

* R317 C-5 R318 D-5 R319 D-5 * R328 C-5 R505 A-3 R506 C-3 R507 A-3 R517 A-3 R520 C-3 R521 B-2 R522 C-2 R525 C-2 R526 C-2 R527 C-2 R528 C-2 R533 B-2 R536 B-2 R540 B-2 R548 B-2 R549 B-2 R554 A-3 R557 A-3 R563 A-3 R564 A-3 R568 A-3 R569 A-3 R573 A-3 * R579 A-4 R582 B-2 R583 B-2 R586 A-3 * R711 B-5 R783 B-4 R785 B-4 R786 B-4 R787 B-4 R788 B-4 R789 B-4 R790 B-4

Dark

- Makes the flash level higher than normal. - Makes the flash level lower than normal. SOLARIZE B& W SEPIA NEG.ART XOFF Sets the special effects for the image (page 60). Adjusts the sharpness of the image. The JJ indicator appears (except when the setting is 0). When the Mode dial is set to M (MOVING IMAGE is set to MPEG MOVIE in the SET UP settings.)

Dscp31

*** Continuous recording with a picture size of 160x112 *** Continuous recording with a picture size of 160x112 , Open the DC IN jack cover, then connect the AC-LS1 AC power adaptor (not supplied) to the DC IN jack of the camera. Connect the cable with the mark facing up. Connect the AC power adaptor to an easily accessible wall outlet (mains) close by. If something goes wrong while you are using the adaptor, immediately shut off the power by pulling the plug out of the wall outlet. , Connect...

Dscp71 Dscp31

, Turn the Mode dial to , turn on the power, and then push the MENU button. You can also carry out this operation when the mode dial is set to SCN. (Spot light-metering) is not displayed on the menu of the DSC-P31 (page 61). , Select 'jjs (Image size) using b B on the control button. Use V V to select the desired image size. , Select (Image quality) using b B on the control button. Use V V to select the desired image quality. When the setting is completed, press the MENU button. The menu...

Ev

* (Spot light-metering) is not displayed on the menu of the DSC-P31 (page 61). * When the subject is at the brightest or darkest ends of the range, or when you are using the flash, the adjustment value set may not actually be used. In normal shooting, the camera makes automatic exposure adjustments. Check the image to be shot, if it looks like the image below, you should make manual adjustments. If you are shooting a back-lit person or a snowy scene, make your adjustments in the + plus...

F

Note 2 Check that the data of page 6, address 02 is 00. If not, turn the power of unit OFF ON. 1) The minipattern box is installed as shown in the following figure. Note 3 The attachment lenses are not used. 2) Install the minipattern box so that the distance between it and the front of lens of camera is less than 3 cm. 3) Make the height of minipattern box and the camera equal. 4) Check the output voltage of the regulated power supply is the specified voltage 0.01 Vdc. 5) Check that the center...

Xjg

All color luminance points should settle within each color reproduction frame. NTSC (NTSC mode) Note 1 Check that the data of page 6, address 02 is 00. If not, turn the power of unit OFF ON. Note 2 Color Reproduction Adjustment is available only once after the power is turned on. Turn the power off, then on again if the adjustment is retried.

File Number

- Assigns numbers to files in sequence even if the Memory Stick is changed. - Resets the file numbering and starts from 0001 each time the Memory Stick is changed. - Displays the menu items, warnings and messages in English. - Displays the menu items, warnings and messages in Japanese.

Hh

A B A B B A Fig. a (Video output terminal output waveform) A B A B B A Fig. a (Video output terminal output waveform) When indicating parts by reference number, please include the board name. Note Les composants identifi s par une marque A sont critiques pour la s curit . Ne les remplacer que par une pi ce portant le num ro sp cifie.

I

O Copying images (for Windows XP users) MJ (continued) Click to remove the checkmark from any images you do not want to copy to your computer, then click Next. The Picture Name and Destination window appears. , Specify the image file names to be copied and the copy destination. Copying of the images starts. When the task is completed, the Other Options window appears. Copy images into the My Documents folder. , Click Nothing. I'm finished working with these pictures, then click Next. The...

Info

Check that the R-Y, B-Y level data (Note 4) satisfies the specified value. Note 6 The adjustment data will be automatically input to page F, address B6 to B7 and DB to EF. Note 6 The adjustment data will be automatically input to page F, address B6 to B7 and DB to EF. Processing after Completing Adjustment Processing after Completing Adjustment

Iso

When recording under dark conditions or recording a fast-moving subject, use a high-number setting. When recording high-quality images, use a low-number setting (except when the Mode dial is set to SCN). 2048x1536 2048 (3 2) 1600x1200 1280x960 640x480 Selects the image size used when shooting still pictures (page 24). 1600x1200 1600 (3 2) 1280x960 640x480 Selects the image size used when shooting still pictures (page 24)

Lsv790a

106 3-056-030-31 ACE (M1.7), 0 PLATE 2 MAIN LOCK 107 3-074-033-01 PLATE, JK FIXED 108 1-684-475-11 FP-073 FLEXIBLE BOARD 109 A-7078-116-A JK-223 BOARD, COMPLETE 110 1-684-474-11 FP-071 FLEXIBLE BOARD 111 3-074-034-01 FRAME, LENS A112 1-476-678-31 FLASH UNIT 113 A-7078-121-A ST-068 BOARD, COMPLETE 114 1-684-472-11 FP-530 FLEXIBLE BOARD 120 1-684-476-11 FP-076 FLEXIBLE BOARD 121 3-713-791-71 SCREW (M1.7X4) 122 1-684-473-11 FP-069 FLEXIBLE BOARD 123 3-074-032-01 HOLDER, AF BOARD, BATTERY D001...

M0v0dddqmpg

Movie files shot normally (page 74) The meanings of the file names are as above stands for any number within the range from 0001 to 9999. The numerical portions of the following files are the same. - A small-size image file shot in E-MAIL mode and its corresponding image file - An image file shot with Clip Motion and its corresponding index image file

Menu

, Press the MENU button, and select DELETE using the V on the control button, then press the center Z. At this point, the images have not yet been deleted. , Select OK using on the control button, then press the center Z. When MEMORY STICK ACCESS disappears, the image has been deleted. Use V on the control button to select CANCEL, then press the center .

N

To change values for the time and the date that have been previously set, change the Mode dial to SET UP, choose CLOCK SET in SETUP 1 (page 97), then proceed from Step 3. You can also carry out this operation when the mode dial is set to SCN, I , or f l. The POWER lamp lights in green and the CLOCK SET screen appears. , Choose the desired order for the date, the month and the year using on the control button, then push the center Z. You can choose from Y M D (year month day), M D Y, and D M Y....

Negart

Colored to look like an Made to look like a old photograph negative image Colored to look like an Made to look like a old photograph negative image C Select PFX (P. EFFECT) using b B, then select the desired mode using A V. When there is reflected light, or the background of the subject provides a very high contrast, you can adjust the focus to that most appropriate for your subject. You can aim at a particular point, and meter the light to adjust the focus for that point. When the place you...

Notice For The Customers In The United Kingdom

A moulded plug complying with BS 1363 is fitted to this equipment for your safety and convenience. Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse approved by ASTA or BSI to BS 1362, (i.e. marked with or < > mark) must be used. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony...

O

Mode dial settings SCN Multipoint AF When you use Multipoint AF, it calculates the distance in three places, in the center of the image, and to both the left and right of the center, you can shoot with the auto focus function without being dependent on the composition of the image. It is useful when it is difficult to focus on the subject because it is not in the center of the frame. You can focus automatically using the AF range finder in the center of the frame. Control button Q Turn the Mode...

Os

Mac OS 9.1 9.2 Mac OS X(v10.0 v10.1) (For Mac OS 8.5.1, 8.6, or 9.0 users only) 1 Turn on your computer, and set the supplied CD-ROM to the CD-ROM drive. The PIXELA ImageMixer window appears. 3 Click USB Driver. The USB Driver window appears. 4 Double-click the icon of the hard disk containing the OS to open the window. 5 Drag and drop the following two files from the window opened in step 3 to the System Folder icon in the window opened in step 4.

Pc

(The same model of the same destination) After the EVR data is saved and downloaded, check the respective items of the EVR data. (Refer to page 5-2 for the items to be checked.) 1-1. Adjusting items when replacing main parts and boards When replacing main parts and boards, adjust the items indicated by Z in the following table.

Pk062 Board

* D254 A-5 D401 C-4 D402 A-1 D801 B-3 D802 A-2 D803 A-2 * R253 C-6 R254 D-2 R255 A-5 R256 A-5 R257 A-5 * R260 B-6 R261 A-5 R262 A-4 R263 A-4 R264 A-4 R265 A-4 R266 A-4 R401 B-4 R402 B-4 R403 B-6 R404 C-4 R405 B-4 R406 B-4 * R407 D-6 R409 C-4 R411 B-4 R413 B-4 R414 C-4 R415 B-4 R416 B-6 R418 B-4 R419 B-4 R420 B-4 R422 C-4 R423 B-4 R424 C-4 R425 C-4 R426 C-4 R429 D-5 R430 C-5 R431 B-5 R433 C-4 R434 D-4 R435 B-5 R436 A-4 R437 C-5 R440 D-6 R441 D-5 R442 C-6 R443 C-5 R444 D-5 R445 B-4 R446 D-5 R451...

Power Save

The LCD screen will be darker than it is when POWER SAVE is set to OFF. You cannot change the settings for LCD BACKLIGHT at this time (page 98). To make the available shooting time even longer, it is recommended that you turn off the LCD screen and use the Finder to do your shooting (page 32). In Flash mode, the (No flash) is displayed. If you want to shoot using the flash, press ( ) on the control button, and select (forced flash) or Auto (page 30). When the power turns on, the Flash mode is...

R

For further details on the items displayed, see page 103. Just as with the AE AF lock indicator on the LCD screen display, when the AE AF lock lamp of the Finder section stops flashing and remains lit, you can start shooting again (page 26). When the LCD screen display is turned off, the digital zoom does not function (page 28). When the LCD screen display is turned off, if you press the (Flash mode) (Self-timer) X (Macro, DSC-P71) or (Spot lightmetering, DSC-P31), the image will be displayed...

Repeat

OFF Plays through the images one time and then stops. Select START using V V b B, then press the center z. In Step 0, select CANCEL, then press the center z. To stop the playback of the slide show Press the center , select EXIT using B, then press the center . To fast forward or to go back to a previous image during a slide show Press the B (Forward), or the b (Backward). The interval settings are just guidelines. The actual intervals will differ, based on...

Restart

A problem with the lens caused an error. - When a message starting with a letter of the alphabet appears Your camera has a self-diagnostics display. This function displays the condition of the camera on the LCD screen using a combination of a letter and four numerical digits. If this occurs, check the following code chart and take the corresponding countermeasure. The last two digits (indicated by )will differ depending on the state of the camera. There is trouble with your camera's hardware,...

S

B Select the image you want to delete using b B. Select DELETE using b B and press the center z. You have not deleted the image yet at this point. Select OK using and press the center z. MEMORY STICK ACCESS appears on the screen. The image has been deleted when the message disappears. Select CANCEL in Step 5, and press the center z. Deleting on the Index (9 images) screen Q Turn the Mode dial to and press the W zoom button once to display an Index (9 images) screen. 0 Select DELETE using b B...

Safety Checkout

After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. 2. Check the interboard wiring to ensure that no wires are pinched or contact high-wattage resistors. 3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them...

Section 5 Adjustments

EVR Data Re-writing Procedure When Replacing Board The data that is stored in the repair board, is not necessarily correct. Perform either procedure 1 or procedure 2 or procedure 3 when replacing board. Save the EVR data of the machine in which a board is going to be replaced. Download the saved data after a board is replaced. Save the EVR data of the machine in which a board is going to be replaced. Download the saved data after a board is replaced. When the data cannot be saved due to...

Ss

BT401 (BATTERY, LITHIUM SECONDARY) Board on the mount position. (See page 4-47.) The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifi s par une marque 0 sont critiques pour la s curit . Ne les remplacer que par une pi ce portant le num ro sp cifi .

Supplement1

File this supplement with the service manual. Change of the end number of the board. CD-391, PK-062, JK-223, ST-068 board the end number of the board has been changed from the end number of the board has been changed from Note Brazilian model is same as other models except accessories. Accessories (Brazilian model) 1-824-009-81 CORD, CONNECTION (AV CONNECTING 1.5m) 1-823-932-11 CORD, CONNECTION (USB 5P) 3-074-757-01 CASE, BATTERY CARRYING

This Note Is Common For Wiring Boards

(In addition to this, the necessary note is printed in each block) Pattern from the side which enables seeing. (The other layers' patterns are not indicated) Circled numbers refer to waveforms. There are a few cases that the part printed on diagram isn't mounted in this model.

Unleaded Solder

Boards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead. (Caution Some printed circuit boards may not come printed with the lead free mark due to their particular size) Unleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40 C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons...

Up

When you are using digital zoom, you cannot confirm the image using the finder. When you are using the digital zoom feature, the Auto focus frame is not displayed. For close-ups of small subjects like flowers or insects, shoot using the Macro feature. You can use this feature for close-ups of subjects up to the distances specified below. When the zoom is set all the way to the W side distances up to 10 cm (3 15 16 inches) from the end of the lens When the zoom is set all the way to the T side...

X

When remove a connector, don't pull at wire of connector. It is possible that a wire is snapped. When installing a connector, don't press down at wire of connector. It is possible that a wire is snapped. Cut and remove the part of gilt which comes off at the point. (Be careful or some pieces of gilt may be left inside) Discharging of the ST-068 board's charging capacitor (C510) The charging capacitor (C510) of the ST-068 board is charged up to the maximum 300 V potential. There is a danger of...

X39523161 307403101 396872971 A7078175a 307403701

CABINET (FRONT) ASSY WINDOW, OVF SCREW (M2), LOCK ACE, P2 FP-527 FLEXIBLE BOARD, COMPLETE PLATE, FLEXIBLE FIXED 6 3-073-338-01 SCREW (DIA. 1.7X4), PRECISION 7 3-713-791-01 SCREW (DIA. 1.7X4.5), PRECISION 8 1-477-243-11 SWITCH BLOCK, CONTROL 9 X-3952-308-1 CABINET (UPPER) ASSY

Memory Stick Error

When failed in the focus and zoom initialization. Checking of flash unit or replacement of flash unit. Abnormality when flash is being charged. Battery pack is not inserted correctly. Battery pack was installed or removed when using the AC adaptor. The camera has a self-diagnosis display. This function displays the camera condition with five-digits (a combination of a letter and figures) on the LCD screen. If this occurs check the following code chart The five-digits display informs you of the...