O CybershotCD

Image device

7.66 mm (1/2.4 type) color CCD Primary color filter Total pixels number of camera

Approx. 5 255 000 pixels Effective pixels number of camera

Approx. 5 090 000 pixels Lens Carl Zeiss Vario-Tessar 3x zoom lens f = 6.7 - 20.1 mm (38 - 114 mm when converted to a 35 mm still camera) F3.5 - 4.4 Exposure control

Automatic exposure, Scene selection (8 modes) White balance

Automatic, Daylight, Cloudy, Fluorescent, Incandescent, Flash File format (DCF compliant)

Still images: Exif Ver. 2.2 JPEG compliant, DPOF compatible Audio with still image: MPEG1 compliant (Monaural) Movies: MPEG1 compliant (Monaural)

Recording media

"Memory Stick Duo" Flash Recommended distance (ISO set to Auto):

0.3 m to 1.5 m (11 7/8 inches to 59 1/8 inches) (W) 0.5 m to 1.5 m (19 3/4 inches to 59 1/8 inches) (T)

[Input and Output connectors] Multi connector

[LCD screen] LCD panel

6.2 cm (2.5 type) TFT drive Total number of dots

211200 (960x220) dots

SPECIFICATIONS

[General]

Used battery pack

NP-FT1 Power requirements

Power consumption (during shooting)

Operating temperature

0°C to +40°C (+32°F to +104°F) Storage temperature

91 X 60 X 21 mm (3 5/8 X 2 3/8 X 2 7/32 inches) (W/H/D, excluding maximum protrusions) Mass Approx. 180 g (6.3 oz) (including battery pack NP-FT1, "Memory Stick Duo" and wrist strap) Built-in microphone

Electret condenser microphone Built-in speaker

Piezo-electric speaker Exif Print Compatible PRINT Image Matching II Compatible

■UC-TA USB cradle [Input and Output connectors]

A/V OUT (MONO) jack (Monaural)

Minijack

Video: 1 Vp-p, 75 n, unbalanced, sync negative Audio: 327 mV (at a 47 kn load) Output impedance 1 kn

USB jack B

USB connection

High-Speed USB

(USB 2.0 High-Speed compatible)

DC IN jack Camera connector

Power requirements

100 to 240 V AC, 50/60 Hz Current consumption

Power consumption

10 W

Rated output voltage

Operating temperature

0°C to +40°C (+32°F to +104°F) Storage temperature

Approx. 47 x 30 x 80mm (1 7/8 x 13/16 x 31/4 inches) (W/H/D, excluding projecting parts) Mass Approx. 170 g (6.0 oz) excluding power cord (mains lead)

■ NP-FT1 battery pack Used battery

Lithium-ion battery Maximum voltage

Nominal voltage

■ Accessories

• Operating instructions (1)

Design and specifications are subject to change without notice.

CAUTION :

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer.

1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges.

2. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.

4. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement.

5. Check the B+ voltage to see it is at the values specified.

6. Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270°C during repairing.

• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering or unsoldering.

Unleaded solder

Boards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)

: LEAD FREE MARK

Unleaded solder has the following characteristics.

• Unleaded solder melts at a temperature about 40°C higher than ordinary solder.

Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C.

Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.

TABLE OF CONTENTS

1. SERVICE NOTE

2. DISASSEMBLY

2-1. DISASSEMBLY 2-1

2-2. SERVICE POSITION 2-3

2-3. CIRCUIT BOARDS LOCATION 2-5

2-4. FLEXIBLE BOARDS LOCATION 2-5

HELP (List of caution points is shown here.)

3. BLOCK DIAGRAMS

3-1. OVERALL BLOCK DIAGRAM (1/2)

3-2. OVERALL BLOCK DIAGRAM (2/2)

5. REPAIR PARTS LIST

5-1. EXPLODED VIEWS 5-1

5-1-1. OVERALL SECTION 5-3

5-1-2.BATTERY HOLDER SECTION 5-4

5-1-3.CABINET (REAR) SECTION 5-5

5-2. ELECTRICAL PARTS LIST 5-6

Parts list of the SY-95, MS-148 and LD-140 boards are not shown.

Pages from 5-7 to 5-11 are not shown.

4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

4-1. FRAME SCHEMATIC DIAGRAM (1/2) 4-1

FRAME SCHEMATIC DIAGRAM (2/2) 4-3

4-2. SCHEMATIC DIAGRAMS

SCHEMATIC DIAGRAM 4-7

SCHEMATIC DIAGRAM 4-9

SCHEMATIC DIAGRAM 4-11

SCHEMATIC DIAGRAM 4-13

Shematic diagram of the SY-95, MS-148 and LD-140

boards are not shown.

Pages from 4-15 to 4-36 are not shown.

4-3. PRINTED WIRING BOARDS

PRINTED WIRING BOARD 4-41

PRINTED WIRING BOARD 4-42

PRINTED WIRING BOARD 4-43

Printed wiring board of the SY-95, MS-148, LD-140 and FP-694 boards are not shown. Pages from 4-45 to 4-52 are not shown.

4-4. MOUNTED PARTS LOCATION 4-53

Mounted parts location of the SY-95, MS-148 and FP-695 boards are not shown. Pages from 4-54 to 4-55 are not shown.

SECTION 1 SERVICE NOTE

NOTE FOR REPAIR

Make sure that the flat cable and flexible board are not cracked of bent at the terminal.

Do not insert the cable insufficiently nor crookedly.

When remove a connector, don't pull at wire of connector. Be in danger of the snapping of a wire.

Cut and remove the part of gilt which comes off at the point. (Take care that there are some pieces of gilt left inside)

When installing a connector, don't press down at wire of connector. Be in danger of the snapping of a wire.

[Discharging of the FLASH unit's charging capacitor]

The charging capacitor of the FLASH unit is charged up to the maximum 300 V potential.

There is a danger of electric shock by this high voltage when the capacitor is handled by hand. The electric shock is caused by the charged voltage which is kept without discharging when the main power of the DSC-T1 is simply turned off. Therefore, the remaining voltage must be discharged as described below.

Preparing the Short Jig

To preparing the short jig. a small clip is attached to each end of a resistor of 1 kQ /1 W (1-215-869-11)

Wrap insulating tape fully around the leads of the resistor to prevent electrical shock.

Discharging the Capacitor

Short circuits between the positive and the negative terminals of charged capacitor with the short jig about 10 seconds.

[Description on Self-diagnosis Display]

Self-diagnosis display

The camera has a self-diagnosis display. This function displays the ^

camera condition with five-digits (a f > 2% ' "

combination of a letter and figures) on the LCD screen. If this occurs check the following code chart. The five-digits display informs you of the camera's current condition. The last two digits--

(indicated by □□) will differ depending on the state of the camera. Se|f-diagnosis display

The contents which can be handled by customer, are displayed.

The contents which can be handled by engineer, are displayed.

Display Code

Countermeasure

Cause

Caution Display During Error

C:32:01

Turn off the main power then back on.

Trouble with hardware.

SYSTEM ERROR

Format the memory stick with the DSC-T1.

• The type of memory stick that cannot be used by this machine, is inserted.

• Unformatted memory stick is inserted.

MS ERROR

E:91:01

Checking of flash unit or replacement of flash unit.

Abnormality when flash is being charged.

Flash LED Flash display Flashing at 3.2 Hz

E:01:XX

Checking of lens drive circuit

When failed in the focus initialization.

E:61:00 *1

E:61:10 *1

Note : The error code is cleared if the battery is removed, except defective flash unit. *1: The error display is given in two ways.

' t i V*

SECTION 2 DISASSEMBLY

The following flow chart shows the disassembly procedure.

2-1. DISASSEMBLY

Note: The power capacitor of the flash unit is charged up to 315 V maximum. If you touch the capacitor terminal that is charged to high voltage, you will receive an electric shock. This high voltage is not discharged even if you turned off the main power of this set, and it residues. Discharge the residual voltage referring to the service note (page 1-1).

® Remove the control switch block in the direction of the arrow.

Dsc S730 Lens Repa

® Lens section

© Five screws (M1.4 x 2.5), lock ace, p2 (special)

® Cabinet (front) assembly ® Lens shaft

® Lens section

Dsc Lens Cover Repair

© FP-690 flexible board (19P)

® ST-86 board, ST terminal cover

© Five screws (M1.4 x 2.5), lock ace, p2 (special)

® Cabinet (front) assembly ® Lens shaft

I HELP 06 1

Note: Do not peel off the radiation sheet as much as possible. If you peel it off, be careful not to damage the flexible board.

© FP-690 flexible board (19P)

® ST-86 board, ST terminal cover

(Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.)

Note: When re-assembling, confirm the switch position.

® FP-695 board (Including the LD-140 board) I HELP 01 I

I HELP 06 1

Note: Do not peel off the radiation sheet as much as possible. If you peel it off, be careful not to damage the flexible board.

® FP-695 board (Including the LD-140 board) I HELP 01 I

Note: The CCD imager is not supplied as a single unit since removing it as a single unit requires adjustment.

HELP 08

(disassembly of the Battery holder section)

© Copper leaf protection sheet ® Flexible board (from LSV-850A)(21P) ® FP-695 board (Including the LD-140 board) ® Radiation sheet (CCD) ® Insulating sheet (CCD) ® Two tapping screws (B1.2 x 3.5)

HELP 08

(disassembly of the Battery holder section)

® Battery holder section

© Turn over the control switch block in the direction of the arrow. ® LCD unit (ACX500EN-J) (25P)

Note: The CCD imager is not supplied as a single unit since removing it as a single unit requires adjustment.

I HELP 05 I

® Microphone

® Microphone

o ®

® Control switch block (PW-125)

© Harness protection sheet ® Two claws ® Microphone holder ® Two solderings ® Microphone cushion

® Control switch block (PW-125)

© Block light guide plate

© Block light guide plate

Mode knob

©

=

_

v

© Remove the solderings ® Four claws

® Cabinet (rear) assembly

©

Tape (LCD)

®

Control switch block,

®

Four screws (M1.4 x 2.5),

LCD frame

lock ace, p2 (special)

®

LCD unit (ACX500EN-J)

®

Screw (M1.4 x 2.5),

Block light guide plate

lock ace, p2 (special)

7

Zoom button

©

Slide the mode knob

®

SW button

2-2. SERVICE POSITION

Vario Tessar Exploded View

2. disassembly

[SERVICE POSITION TO CHECK THE SY-95 BOARD]

Notel: By using an adhesive tape, press the LENS COVER switch (S401).

Note2: When checking the VIDEO AMP (SY-95 board IC302) or the USB circuit, connect the cradle.

Usb Ccd Schematics

CN402

CN701 CN703

SY-95 board

CN702

CN-198 board

AC IN

AC power adaptor

CCD block assembly (33P)

Lens section

S401 LENS COVER switch (Notel)

FP-693 flexible board (16P)

Control switch block (PW-125)

FP-690

flexible board (19P)

LCD unit (ACX500EN-J), Block light guide plate

-148 board

CN704 CN705

Note : The power capacitor of the flash unit is charged up to 315 V maximum. If you touch the capacitor terminal that is charged to high voltage, you will receive an electric shock This high voltage is not discharged even if you turned off the main power of this set, and it residues. Discharge the residual voltage referring to the service note (page 1-1).

2. disassembly

2-3. CIRCUIT BOARDS LOCATION

MS-148

NAME

FUNCTION

CD-463

CCD IMAGER

CN-198

MULTI CONNECTOR

LD-140

LENS DRIVE

MS-148

MS I/O, LCD PANEL DRIVE

ST-86

FLASH

SY-95

CAMERA A/D CONVERTER, TIMING GENERATOR, CAMERA DSP, LENS CONTROL, CAMERA SYSTEM CONTROL, HI CONTROL, AUDIO I/O, FLASH DRIVE, DC/DC CONVERTER, CONNECTOR

2-4. FLEXIBLE BOARDS LOCATION

The flexible boards contained in the lens block are not shown.

FP-693

DIY Battery Repair

DIY Battery Repair

You can now recondition your old batteries at home and bring them back to 100 percent of their working condition. This guide will enable you to revive All NiCd batteries regardless of brand and battery volt. It will give you the required information on how to re-energize and revive your NiCd batteries through the RVD process, charging method and charging guidelines.

Get My Free Ebook


Post a comment